Sharp PN-V601 manual Remote Control Mode, Press or , select the mode, then perform settings

Remote Control Mode

With the remote control unit it’s possible to perform operation

of...

•The primary monitor

•Monitors with a specified ID No.

•All primary/secondary monitors

It’s necessary to specify which type of operation will be performed in advance.

1.If using the remote control unit, press MODE for approx 5 seconds.

If using the monitor buttons, hold both			and at
the same time on the primary.
REMOTE CONTROL MODE
		▲ THIS MONITOR ONLY▲
	MODE

Operate this monitor.

OK CANCEL

2. Press or , select the mode, then perform settings.

THIS MONITOR ONLY

Performs operation of only the primary using the remote control unit.

[Example] If the volume is lowered, the volume of the primary will lower.

Secondary	Primary
ID No.: 2	ID No.: 1
	VOLUME 10
Secondary	Secondary
ID No.: 3	ID No.: 4

Press to lower the volume

SPECIFIED MONITOR

Performs operation of a monitor with a specified ID No. using the remote control unit.

Press or to select ID No., then press or to select the ID No. of the monitor that you will operate.

*When it receives signals from the remote control unit,

“Operating specified monitor.” will be displayed on the primary screen.

[Example.] If ID No. is set to 3 and the volume is lowered, the volume of the monitor for ID No.: 3 will lower.

Secondary	Primary
ID No.: 2	ID No.: 1
Secondary	Secondary
ID No.: 3	ID No.: 4
VOLUME 10

Press to lower the volume

When you would like to confirm the ID No. that is set to the

monitor, press or to select ID No. DISPLAY, then press . The ID No. will be displayed on the screen.

ALL MONITORS

Performs operation of all primary/secondary monitors.

*ALL will be displayed on the menu of the primary.

*When it receives signals from the remote control unit,

“Operating all monitors.” will be displayed on the secondary screen. (Excluding power and input mode selection operation)

*Settings may not be reflected depending on the state of the connected monitors.

[Example] If the power for the primary is turned ON, the power for all the monitors will be turned ON.

		Secondary	Primary
		ID No.: 2	ID No.: 1
		Power ON	Power ON
		Secondary	Secondary
		ID No.: 3	ID No.: 4
		Power ON	Power ON
		Press POWER to turn the power ON
Press	or	to select EXPAND ITEM, and press		or

to select to perform this action or not.

OFF ...........For all monitors, only power, input mode

selection, and product information display operations will be recognized.

ON .............For all monitors, all operations will be

recognized.

After returning to the normal screen with procedure 3, when 5 minutes have passed from the end of operation, it will automatically return to OFF.

ALL [EXPAND ITEM] will be displayed on the menu of the primary.

*Even when REMOTE CONTROL MODE is set to ALL MONITORS, certain settings such as LAN settings and ID No. settings will not be reflected on the other monitors.

3.Press or to select OK, then press MENU and return to the normal screen.

4.Perform operation.

Caution

•When the remote control mode is set to ALL MONITORS and EXPAND ITEM is set to ON, performing remote control operations that change adjustment values will result in the secondary adjustment values being the same as the primary adjustment values.

Secondary	Primary	Secondary	Primary
ID No.: 2	ID No.: 1	ID No.: 2	ID No.: 1
VOLUME 12	VOLUME 11	VOLUME 10	VOLUME 10

Secondary	Secondary	Secondary	Secondary
ID No.: 3	ID No.: 4	ID No.: 3	ID No.: 4
VOLUME 9	VOLUME 10	VOLUME 10	VOLUME 10

Press to lower the volume

Be careful of this when adjusting individual displays.

TIPS

•You can copy the setting values of the primary to other monitors with COPY SETTING VALUE. (See page 11.)

•The buttons on the monitor itself (primary) are also effective in remote control mode.

•When monitors connected in a daisy chain are in standby mode for LOW POWER, operation cannot be performed for subsequent monitors.

7 E