MOUNTING PRECAUTIONS
•This product is for use indoors.
•Since the monitor is heavy, consult your dealer before installing, removing or moving the monitor.
•When installing, removing or moving the monitor, ensure that this is carried out by at least 2 people.
•A mounting bracket compliant with VESA specifications is required. Do not use any screw holes other than VESA holes for installation.
•To attach a
•When moving the monitor, be sure to hold it with either both handles or the 4 corners on the bottom of the unit. Do not place your hand on the screen. This may cause product damage, failure, or injury.
•Install the monitor with the surface perpendicular to a level surface.
•Mounting the monitor on the wall requires special expertise and the work must be performed by an authorized SHARP dealer. You should never attempt to perform any of this work yourself. Our company will bear no responsibility for accidents or injuries caused by improper mounting or mishandling.
•This monitor should be used at an ambient temperature between 41°F (5°C) and 95°F (35°C). Provide enough space around the monitor to prevent heat from accumulating inside.
For the monitor in horizontal orientation
•Do not block any ventilation openings. If the temperature inside the monitor rises, this could lead to a malfunction.
•After mounting, please carefully ensure the monitor is secure, and not able to come loose from the wall or mount.
•Do not place the monitor on a device which generates heat.
•Use the supplied vertical sticker when you install the monitor in vertical orientation.
Operation panel | Logo |
Do not remove the
• Be sure to use a
• This monitor is designed to be installed on a concrete wall or pillar. Reinforced work might be necessary for some materials such as plaster / thin plastic board / wood before starting installation.
This monitor and bracket must be installed on a wall which can endure at least 4 times or more the weight of the monitor. Install by
| |
2 | 2 |
[5] | [5] |
| 2 [5] |
Unit: inch [cm]
the most suitable method for the material and the structure.
• Do not use the product in locations where the unit is exposed to direct sunlight or other strong light. Since this product operates with infrared rays, such light may cause a malfunction.
■ Connecting the USB cable 
Warning:
•• Contact your dealer or a service engineer to have the USB cable installed or removed.
Risk of electrical shock or injury if you attempt the work yourself.
For the monitor in vertical orientation
• Before connecting the USB cable, turn off the main power switch |
| |
2 | 2 |
[5] | [5] |
| 2 [5] |
Unit: inch [cm]
and disconnect the power cable from the outlet. |
• Use only the supplied USB cable. |
■ Installing the power switch |
•If it is difficult to provide sufficient space for any reason such as the installation of the monitor inside a housing, or if the ambient temperature may be outside of the range of 41°F (5°C) to 95°F (35°C), install a fan or take other measures to keep the ambient temperature within the required range.
•Temperature condition may change when using the display together with the optional equipments recommended by SHARP. In such cases, please check the temperature condition specified by the optional equipments.
•Adhere to the following when installing the monitor in its vertical orientation. Failing to adhere to the following may cause malfunctions.
-Install the monitor such that the power LED is located on the bottom side.
-Set the MONITOR on the SETUP menu to PORTRAIT. (See Operation manual.)
-Be sure to clamp the power cord (supplied) onto the cable clamp attachment below using the supplied cable clamp. When clamping the power cord, take care not to stress the terminal of the power cord. Do not bend the power cord excessively.
Power cord (Supplied)
Cable clamp
E 4 | Cable clamp attachment |
Warning: |
•• Contact your dealer or a service engineer to have the power switch installed or removed.
Risk of electrical shock or injury if you attempt the work yourself.
1.Remove the screw (x1) from the monitor.
2.Remove the protective seal and connect the power switch connector, making sure the connector is in the correct orientation.
3.Align the clamps with the slot in the bottom of the unit and tighten the screws (x2).
Make sure that the clamps are firmly secured. Take care that the cable is not caught or pinched.
4.Replace the screw that was removed in 1.
Protective seal
Connector |
|
| Bottom |
Power switch |
|
Mounting | Mounting |
bracket | bracket |
