Sharp TINSZA625AWZZ, CD-SW440N E-11, Setting the clock Remote control only, Timer playback

Setting the clock (Remote control only)

CD

USB

TAPE

In this example, the clock is set for the 12-hour (AM 12:00) display.

1Press the ON/STAND-BY button to turn the power on.

2Press the CLOCK/TIMER button.

3Within 10 seconds, press the MEMORY button.

Press the or button to select 12-hour or

24-hour display and then press the MEMORY button.

The 12-hour display will appear.

“AM 12:00” (AM 12:00 - PM 11:59)

“AM 0:00”	The 12-hour display will appear.
	(AM 0:00 - PM 11:59)
“0:00”	The 24-hour display will appear.
	(0:00 - 23:59)

4To adjust the hour, press the or button and

then press the MEMORY button. Press the or button once to advance the time by 1 hour. Hold it down to advance continuously.

5To adjust the minutes, press the or button and then press the MEMORY button. Press the

or button once to advance the time by 1 minute.

To confirm the time display:

Press the CLOCK/TIMER button. The time display will appear for about 5 seconds.

Note:

The “CLOCK” will appear or time will be displayed when the AC power supply is restored after a power failure or unplugging the unit. If incorrect, readjust the clock as follows.

To readjust the clock:

Perform “Setting the clock” from step 1. If the “CLOCK” does not appear in step 2, step 3 (for selecting the 12-hour or 24-hour display) will be skipped.

To change the 12-hour or 24-hour display:

1Clear all the programmed contents. [Refer to “Factory reset, clearing all memory” on page 14 for details.]

2Perform “Setting the clock” from step 1 onwards.

Timer and sleep operation (Remote control only)

Once timer:

Once timer play works for one time only at a preset time.

Daily timer:

Daily timer play works at the same preset time every day. For example, set the timer as a wake-up call every morning.

Using the once timer and daily timer in combination: For example, use the once timer to listen a radio program, and use the daily timer to wake up.

1 minute or more

Daily timer Once timer

Start Stop Start Stop

Timer playback

Before setting timer:

●Check that the clock is set to the correct time (refer to page 11). If it is not set, you cannot use the timer function.

●For timer playback: Plug in USB or load disc/cassette or dock iPod to be played.

1Press the ON/STAND-BY button to turn the power on.

2Press and hold the CLOCK/TIMER button.

3Within 10 seconds, press the or button to select “ONCE SET” or “DAILY SET”, and press the MEMORY button. Set the clock to the correct time if “ONCE SET” or “DAILY SET” does not appear.

4Within 10 seconds, press the or button to select “TIMER SET”, and press the MEMORY button.

5To adjust the hour, press the or button and then press the MEMORY button.

6To adjust the minutes, press the or button and then press the MEMORY button.

7Set the time to finish as in steps 5 and 6 above.

8To select the timer playback source (CD, TUNER, USB,

iPod, TAPE or AUDIO IN), press the or button. Press the MEMORY button.

When you select the tuner, select a station by pressing

the or button, and then press the MEMORY button. If a station has not been programmed, “NO PRESET” will be displayed and timer setting will be canceled.

9Adjust the volume using the VOLUME control, and then press the MEMORY button. Do not turn the volume up too high.

10Press the ON/STAND-BY button to enter the power stand-by mode. The “TIMER” indicator lights up and the unit is ready for timer playback.

E-11