Manuals / Sharp / Computer Equipment / Projector

Sharp specifications XG-SV100W XG-SV200X, Setup Manual, Data Projector, Model, Troubleshooting

Models: XG-SV100W XG-SV200X

1 26

Download 26 pages 56.08 Kb

Page 1

DATA PROJECTOR

DATA PROJECTOR

MODEL

XG-SV100W

XG-SV200X

SETUP MANUAL

Connecting Pin Assignments	2
RS-232C Speciﬁcations and Commands	4
Operating the Projector Using the PJLink TM Protocol	10
Setting up the Projector Network Environment	11
1. Connecting the Projector to a Computer	12
2. Setting an IP Address for the Computer	13
3. Setting up a Network Connection for the Projector	15
Controlling the Projector via LAN	17
Controlling the Projector Using Internet Explorer	17
Conﬁrming the Projector Status (Status)	18
Controlling the Projector (Control)	18
Setting and Adjusting the Projector (Settings & Adjustments)	19
Setting the Security (Network – Security)	19
Making General Settings for the Network (Network – General)	20
Setting for Sending E-mail when an Error Occurs
(Mail – Originator Settings)	20
Setting Error Items and Destination Addresses to which E-mail is to be
Sent when an Error Occurs (Mail – Recipient Settings)	21
Setting Error Items and the URL that are to be Displayed
when an Error Occurs (Service & Support – Access URL)	21
Resetting the Lamp Timer of the Projector via LAN	22
Troubleshooting	24

Image 1

Sharp specifications XG-SV100W XG-SV200X, Setup Manual, Data Projector, Model, Connecting Pin Assignments

Contents

Connecting Pin Assignments SETUP MANUALRS-232C Speciﬁcations and Commands Operating the Projector Using the PJLink TM ProtocolCOMPUTER/COMPONENT 1, 2 input and COMPUTER/COMPONENT output Terminals Connecting Pin AssignmentsHDMI Terminal RS-232C Cable recommended connection D-sub 9 pin female connector Connecting Pin AssignmentsLAN Terminal LAN RJ-45 Computer control RS-232C Speciﬁcations and CommandsCommunication conditions Basic formatRS-232C Speciﬁcations and Commands CommandsP O W R RS-232C Speciﬁcations and Commands RS-232C Speciﬁcations and Commands RS-232C Speciﬁcations and Commands 5 The Lamp Timer Reset command is available only in standby mode RS-232C Speciﬁcations and CommandsThe projector conforms with the PJLinkTM standard Class Operating the Projector Using the PJLinkTM Protocol1. Connecting the projector to a computer Setting up the Projector Network Environment2. Setting an IP address for the computer 3. Setting up a network connection for the projectorSetting up the Projector Network Environment 1. Connecting the Projector to a ComputerSetting up the Projector Network Environment 2. Setting an IP Address for the Computer6 Conﬁrm or change an IP address for the setup computer Setting up the Projector Network EnvironmentIP address Subnet mask Default gateway Do not input any values Setting up the Projector Network Environment 3. Setting up a Network Con- nection for the ProjectorClick the “Apply” button Setting up the Projector Network EnvironmentControlling the Projector Using Internet Explorer Controlling the Projector via LANControlling the Projector Conﬁrming the ProjectorControlling the Projector via LAN Status StatusSetting the Security Setting and Adjusting theProjector Settings & Adjustments Controlling the Projector via LANSetting for Sending E-mail when an Error Occurs Making General Settings forMail - Originator Settings Controlling the Projector via LANAccess URL Mail - Recipient SettingsResetting the Lamp Timer of the Projector via LAN Resetting the Lamp Timer of the Projector via LAN Communication cannot be established with the projector TroubleshootingTroubleshooting Troubleshooting