Sherwood R-772 manuel dutilisation Room 2 Source Playback

�

VOL ~

(ROOM 2 volume)

R-772(G)2007.9.174:43PM페이지35

ROOM 2 SOURCE PLAYBACK

•This function allows enjoying one source in the main room and playing another in a different room at the same time.

•When you connect the multi-room system kit to the IR IN jack of this receiver, you can control this receiver with not only the universal remote control unit but also the ROOM 2 remote control unit in a different room, too. (For details, refer to "CONNECTING MULTI-ROOM SYSTEM KIT" on page 12 and "ROOM 2 Remote Controls" on page 21.)

�Notes:

•The analog signals from the EXTERNAL INs and the digital signals cannot be output to the different room, meaning no playback in a different room.

•You cannot play the ROOM 2 source in any surround mode.

ENGLISH

■When using the buttons on the remote control unit.

1. Press the ROOM 2 button.

• ROOM 2 ~ is displayed for several seconds.

• Each time this button is

pressed, the ROOM 2 mode changes as follows :

OFF : To turn off the ROOM 2

�function. ("R2" goes off .)

ON : To turn it on. ("R2" lights up.)

�Note :

•When the ROOM 2 mode is set to OFF, you cannot adjust the ROOM 2 volume.

2. Select the desired input as a ROOM 2 source.

• Each time the INPUT button on the universal remote control unit is pressed, the ROOM 2 input can be selected among MAIN source, TUNER, CD, AUX, TAPE, VIDEO 1 ~ VIDEO 4.

3. Adjust the ROOM 2 volume.

•You can adjust the volume on the power amplifier

assigned to "BACK ← → ROOM 2" or "ROOM 2" when the ROOM 2 speaker

terminals are connected to the speakers in a different

room. (For details, refer to "When selecting the AMP ASSIGN" on page 40.)

•The MUTE button on the ROOM 2 remote control unit can be available only when the ROOM 2 function is operating.

4. Start play on the component related to the ROOM 2 source.

■When using the buttons on the front panel.

1. Press the ROOM 2 button to enter the ROOM 2 mode.

• ROOM 2 ~ is displayed for several seconds.

•When the ROOM 2 setting mode disappears, press the ROOM 2 button again.

2. Select the desired mode while displaying the ROOM 2 setting mode.

• Each time these buttons are pressed, the mode changes as

follows :
ROOM 2 ~	: To turn on or
(ROOM 2 mode)	off the ROOM 2

�function.

IN ~ : To select the desired ROOM 2 source. (ROOM 2 input)

: To adjust the volume on the power amplifier assigned to "BACK ← → ROOM 2" or "ROOM 2".

�Note : When the ROOM 2 mode is set to OFF, the ROOM 2 input and the ROOM 2 volume cannot be selected

3. Set the selected mode as desired.

■When selecting the ROOM 2 mode. OFF : To turn off the ROOM 2

�function. ("R2" goes off.)

ON : To turn it on. ("R2" lights up.)

■When selecting the ROOM 2 input.

• You can select the desired among MAIN source, TUNER, CD, AUX,

TAPE, VIDEO 1 ~ VIDEO 4 as a ROOM 2 source. ■When selecting the ROOM 2 volume.

•You can adjust the volume on the power amplifier assigned to "BACK ← → ROOM 2" or "ROOM 2" when the ROOM 2 speaker terminals are connected to the speakers in a different room. (For details, refer to "When selecting the AMP ASSIGN" on page 40.)

4. Start play on the component related to the ROOM 2 source.

�Notes:

•When the EXTERNAL IN is selected as a main input, if the MAIN source is selected as a ROOM 2 input, no audio signal can be heard in the different room (ROOM 2).

•Even when this receiver enters the standby mode, in such a case that "R2" lights up still and the POWER ON/STANDBY button lights up blue as it does in the operating mode, meaning only the ROOM 2 circuitry operates, the ROOM 2 source can be played independently.

•When you do not use the ROOM 2 function, turn off the ROOM 2 function to save electricity.

35