Sherwood R-772 manuel dutilisation When selecting the Hdmi Assign, When selecting the Video Assign

R-772(G)2007.9.174:43PM페이지45

Continued

When selecting the HDMI ASSIGN

•You should assign the connected HDMI INs to the desired of VIDEO 1 ~ VIDEO 4. (For details, refer to "CONNECTING VIDEO COMPONENTS" on pages 5 ~ 6.)

•You can select HDMI 1 or HDMI 2.

■Note :

•In such a case that a HDMI IN is assigned to two input sources or more, when these input sources are selected, the uncompressed digital video signals (and digital audio signals when the HDMI AUDIO OUT is set to ON) input into the same HDMI IN can be output from the HDMI MONITOR OUT of this receiver.

When selecting the VIDEO ASSIGN

•You should assign the connected COMPONENT VIDEO INs to the desired of VIDEO 1 ~ 4. (For details, refer to "CONNECTING VIDEO COMPONENTS" on pages 5 ~ 6.)

•You can select the desired of COMP 1 ~ 2.

■Note :

•In such a case that a COMPONENT VIDEO IN is assigned to two input sources or more, when these input sources are selected, the component video signals can be viewed from the same COMPONENT VIDEO IN.

When selecting the VIDEO MODE

• You can select the video input signal to be output from the MONITOR OUTs.

AUTO : When there are multiple video input signals, the video input signals are detected and the video input signal to be output from the MONITOR OUTs is selected automatically in the following order :

component video, S-video, composite video.

COMPOSITE : The signal that is input into the (COMPOSITE) VIDEO jack is always played. The composite video input signal is

up-converted and output from the S-VIDEO MONITOR OUT jack.

S-VIDEO : The signal that is input into the S-VIDEO jack is always played. The S-video input signal is down-converted and

output from the (COMPOSITE) VIDEO MONITOR OUT jack.

COMPONENT : The signals that are input into the COMPONENT jacks are always played.

Because video conversion is not performed, no video signals are output from the MONITOR OUT jacks when there are no video signals that are input into the COMPONENT jacks.

•For details, refer to "Relationship between the video input signal and the video output signal" on page 6.

■Note :

•When selecting the VIDEO 4, S-VIDEO cannot be selected.

When selecting the AUDIO ASSIGN

•You should assign the connected DIGITAL INs to the desired of CD, AUX and VIDEO 1 ~ VIDEO 4. (For details, refer to "CONNECTING DIGITAL INS AND OUT" on page 8.)

•You can select the desired of OPT 1, OPT 2, COAX1 and COAX 2.

■Note :

•In such a case that a DIGITAL IN is assigned to two input sources or more, when these input sources are selected, the digital audio signals can be heard from the same DIGITAL IN.

When selecting the AUDIO MODE

•You can select the desired audio input signal to be played.

■Notes :

•Be sure to set the AUDIO MODE to the audio input which is connected and assigned to the selected input source.

•When the HDMI AUDIO OUT is set to ON, no sound will be heard from the speakers connected to this receiver (except ROOM 2 speakers).

•When the AUDIO MODE is set to HDMI, you should set the HDMI ASSIGN correctly. If not, "H1", "H2" (, meaning no digital audio signal input from it) or "Hd" (, meaning no HDMI assignment) flickers on the unit's display and no sound will be heard.

•When the AUDIO MODE is set to DIGITAL, you should set the AUDIO ASSIGN correctly. If not, "o1", "c1", etc.(, meaning no digital signal input from it) or "d" (, meaning no audio assignment) flickers on the unit's display and no sound will be heard.

AUTO : When there are multiple audio input signals, the audio input signals are detected and the audio input signal to be played is selected automatically in the priority order of them :

HDMI audio > DIGITAL audio > ANALOG audio HDMI : The signal that is input into the HDMI IN is always played.

DIGITAL : The signal that is input into the OPTICAL or the COAXIAL DIGITAL IN is always played.

ANALOG : The signal that is input into the analog AUDIO INs is always played.

ENGLISH

45