Sherwood RV-4060R manual Additional Information

SLEEP

The sleep mode allows the system to continue to operate for a specified period of time before automatically shutting off.

Press the SLEEP button on the remote control to set the receiver to automatially turn off after 10, 20, 30, 60 or 90 minutes.

–Each time the button is pressed, the setting is changed as below;

10 20 30 60 90 OFF

Select the required sleep time by pressing SLEEP : 10, 20, 30, 60 or 90 minutes.

Notes:

–During an active sleep timer period, you can reset the SLEEP time again by pressing the SLEEP button.

–A sleep timer period will be cancelled when you switch your system to standby (using the POWER button on your remote control).

RECORDING WITH A CASSETTE DECK

Select the desired input to be recorded.

Start recording on the TAPE MONITOR.

Start play on the desired input.

–For tape monitor function, refer to amplifier chapter titled "TAPE MONITOR function".

DUBBING FROM VCR2 TO VCR1

Select VCR2 as program source to be recorded. Start recording on the VCR1.

Start playback on the VCR2.

–The audio and video signals from VCR2 will be dubbed onto the tape in VCR1.

When dubbing from VCR2 to VCR1, you can replace the audio signal from VCR2 with the signal from an audio source, e.g. a CD player.

First select VCR2 as program source to be recorded. Then select the required audio source.

Start recording on the VCR1.

Start playing back on the audio alternate source and on the VCR2.

–You can now watch the picture from VCR2 on your TV and listen to the sound from the audio source while recording.

ADDITIONAL INFORMATION

TECHNICAL SPECIFICATIONS

AMPLIFIER SECTION
Output power : Continuous Average (left/right),
8 Ω , THD 0.7%, 40 Hz~20 kHz				2	50 W
Surround mode :
front				2	35 W
rear					35 W
center					35 W
Total harmonic distortion, 1 kHz					0.3%
Intermodulation distortion					0.5%
Frequency response, 1 W,-3 dB
linear			30 Hz~40 kHz
Signal - to - Noise Ratio, IHF "A" weighted					90 dB
Stereo Separation, 1 kHz					55 dB
Damping factor, 8 Ω					40
Bass/Treble control, 100 Hz/10 kHz				+/-10 dB
Input Sensitivity
Linear inputs		180 mV (rated output)
Outputs
Recording, 2.5 kΩ				200 mV
Headphones				8-1,000 Ω
speakers		Front L/R, Center : 8Ω
				Rear : 4Ω
FM TUNER SECTION
Tuning frequency range			87.5~107.9 MHz
Usable sensitivity				17.2 dBf
50 dB quieting selectivity, mono/stereo			21.2/41.2 dBf
Signal to noise ratio, 65 dBf, mono/stereo				68/65 dB
Total harmonic distortion, 65 dBf, 1 kHz, mono/stereo
				0.3/0.5 %
Frequency response, 30~15,000 kHz				+/-1 dB
Stereo separation, 1 kHz					32 dB
Capture ratio				1.25 dB
IF rejection retio					75 dB
AM TUNER SECTION
Tuning frequency range			520~1710 kHz
Usable sensitivity				800 µv/m
Signal to noise ratio					40 dB
Selectivity					25 dB
POWER SUPPLY
Mains voltage				120 V/60 Hz
Power consumption					140 W
Main outlet		1 A or 100 W max.
CABINET
Dimensions (w h d)	440	110	280 mm approx
(17-5/16		4-11/16		11 inches)
Weight			7.5 kg approx
				(16.5 lbs)
ACCESSORIES
Remote control unit					1x
AM Loop Antenna					1x
FM T Antenna					1x
Note : Design and specifications subject to change
without notice for improvements.

MAINTENANCE

Do not leave the unit in direct sunlight or other places where high temperatures can occur for any length of time, such as in the vicinity of a heating source.

Do not expose the equipment to humidity or rain.

A chamois leather cloth, slightly moistened with water is sufficient for cleaning the cabinet.

Do not use cleaning agents containing alcohol, spirits, ammonia or abrasives.

ENGLISH

11