Shure AXS58 System And Component Specifications, AXB1, AXB1G BODYPACK TRANSMITTER SPECIFICATIONS

English

SYSTEM AND COMPONENT SPECIFICATIONS

RF Carrier Frequency Range

169.445 to 240.000 MHz

Operating Range:100 m (328 ft.) under typical conditions Audio Frequency Response: 50 to 15,000 Hz, ￿3 dB Image Rejection: 75 dB typical

Spurious Rejection: 75 dB typical

System Distortion (ref. ￿15 kHz deviation, 1 kHz modula- tion): 0.1% THD typical

Signal/Noise Ratio: 102 dB

Sensitivity: ±110 dBm for 12 dB SINAD typical

Operating Temperature Range

±18° to 57° C (0° to 135° F) NOTE: Battery characteristics may limit this range.

Battery Life: 18 hours with 9 V alkaline battery (Duracell MN1604 recommended).

AXB1, AXB1G BODYPACK

TRANSMITTER SPECIFICATIONS

RF Output	50 mW Typical
Input	Unbalanced
Configuration
	1/4 Inch (AXB1G); 4-pin Tini Q-G(AXB1)
Connector Type
Actual Impedance	1 MΩ
Maximum	+12 dBV
Recommended
Input Level*
Minimum	±80 dBV
Recommended
Input Level**
Connector Pin	Pin 1:Tied to Ground
	Pin 2:Tied to +5 V
Assignments
	Pin 3:Tied to Audio
(AXB1)
	Pin 4:Tied to 20kΩ Resistor and Audio Ground
Connector Pin	Sleeve: Tied to Ground
Assignments
	Tip: Tied to Audio
(AXB1G)
Dimensions	64 mm H x 106 mm W x 24 mm D
	(2.52º H x 4.17º W x 0.95º D)
Net Weight	96.4g (3.4 oz.)
Power	9 V alkaline battery (Duracell MN1604
Requirements	recommended); 8.4 V NiCd battery optional.
Nominal Current	30 mA
Drain

*Gain Control at minimum

**Gain Control at maximum

AXR3 AND AXR4N RECEIVER SPECIFICATIONS

	AXR4N	AXR3
Connector	3-Pin XLR (Male) and	1/4º Phone Jack
	1/4º Phone Plug
Maximum Output	1/4º: + 5dBV	±6.8 dBV
Levels at 15 KHz	XLR: ±10 dBV
deviation
Nominal Output	1/4º: ±8 dBV	±32 dBV
Levels	XLR: ±30 dBV
Output Configuration	Active Balanced	Unbalanced
Actual Impedance	3.3 KΩ	1 KΩ
Connector Pin	XLR: Pin 1: ground;	Tip: hot; Sleeve:
Assignments	Pin 2: hot; Pin 3: cold	ground
	1/4º: Tip: hot; Sleeve:
	ground.
Dimensions (AXR4N)	41 mm H x 197 mm W x 138 mm D
	(1.625º H x 7.77º W x 5.42º D)
Dimensions (AXR3)	35mm H x 152 mm W x 98 mm D
	(1.38ºH x 5.98º W x 3.85º D)
Net Weight (AXR4N)	435 g (15.4 oz.)
Net Weight (AXR3)	192 g (6.8 oz.)
Power Requirements	12±18 VDC nominal, 200mA
Power Supply	120 V or 230V AC adaptor with 2.1 mm female
	plug
Voltage/Current/Phant	Yes	Yes
om Power Protection

Certification

AXB1G, AXB1:Accepted under FCC Parts 74 and 90. Certi- fied by IC in Canada under TRC-78.

AXH2/31, AXH2/58: Type Accepted under FCC Parts 74 and 90. Certified by IC in Canada under TRC-78. Conforms to European Union directives, eligible to bear CE marking; meets European Union Requirements. Type Approval: pr I±ETS 300 422, BZT 17 TR 2019, and BAPT 122 R 1. EMC Immunity: pr ETS 300 445.

AXR3, AXR4N: Approved under the Declaration of Conformity provision of FCC Part 15 (AXR3). Certified by IC in Canada under RSS 123 (AXR4N). Conforms to European Union di- rectives, eligible to bear CE marking; mets European Union Requirements. EMC Immunity: pr ETS 300 445. Power sup- ply meets Low Voltage Directive: 73/23/EEC.

AXH2 HAND-HELD TRANSMITTER SPECIFICA- TIONS

	AXH2/58 (SM58)		AXH2/31(BG3.1)
RF Output	50 mW Typical (FCC); 20 mW Typical (ETSI)
Dimensions	236 mm H x 51 mm D		222 mm H x 51 mm D
	(9.29º H x 2.01º D)		(8.74º H x 2.01º D)
Net Weight	295g (10.4 oz.)		266g (9.4 oz.)
Power Requirement	9 V alkaline battery (Duracell MN1604 recom-
	mended); 8.4 V NiCd	battery optional.
Nominal Current	30 mA		30 mA
Drain

7