TROUBLESHOOTING
Alert Message | Explanation/Solution |
|
|
No Hardware Detected | S Make sure the UA888 Interface Module is turned on. |
| S Make sure the U4 Receiver is turned on. |
| S Make sure all cables are properly connected. |
| S Check for broken or intermittent cables |
| S Check COM Port selection in the Shure Wireless Workbench program. |
|
|
Failed to program. | S Make sure the U4 Receiver is turned on. |
| S Make sure the UA888 Interface Module is turned on. |
|
|
COM [x] not receiving data. | S Improper COM port (serial port) selected. |
| S Go to [Devices>Configure Connections], and select the proper COM port. |
| S Make sure all cables are properly connected. |
|
|
UA888 SPECIFICATIONS
Operating Voltage |
|
+5 Vdc supplied by Shure U4 receiver. |
|
Operating Current |
|
45 mA per input |
|
Temperature Range |
|
Operating: |
|
Storage: |
|
Dimensions |
|
44 mm H x 482 mm W x 295 mm D |
|
(1 3/4 in x 19 in x 11 5/8 in) |
|
Net Weight |
|
930 g (2.1 lbs) |
|
Furnished Accessories | Part No. |
| |
25 pin Cable | 95A8745 |
95A8676 | |
CD ROM |
Certification
FCC Verified under Part 15 as a Class B digital device.
This Class B Digital Apparatus complies with Canadian
Conforms to European EMC Directive 89/336/EEC, eligible to bear CE marking. Meets EMC requirements as an ancillary de- vice per EN 301 489, Parts 1 and 9.
UA111 SPECIFICATIONS
Operating Voltage
+5 Vdc, supplied by Shure U4 receiver
Operating Current
45 mA
Temperature Range
Operating:
Storage:
Dimensions
63.5mm H x 55.6 mm W x 16.5 mm D
(2.5 in. H x 2.19 in. W x 0.65 in. D)
Net Weight
38 g (1.34 oz.)
Furnished Accessories
CD ROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Certification
Authorized under the Declaration Of Conformity provision of FCC Part 15 as a Class B Digital device.
This Class B Digital Apparatus complies with Canadian
Conforms to European EMC Directive 89/336/EEC, eligible to bear CE marking. Meets EMC requirements as an ancillary de- vice per EN 301 489, Parts 1 and 9.
Information to User
Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate this equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, try to correct it through one of the following measures:
S | Reorient or relocate the receiving antenna. | S | Connect the equipment into an outlet on a circuit differ- |
S | Increase the separation between the equipment and |
| ent from that to which the receiver is connected. |
| Consult your dealer or an experienced radio/TV techni- | ||
| receiver. | S | |
|
|
| cian for help. |
Under extremely abnormal conditions, electrical transients on the power line may interrupt communication between the UA888/UA111 Inter- face Module and the computer. The UA888/UA111 will not be damaged; normal operation will resume.
NOTE: Do not use cables longer than 3.1 m (10 ft.) to connect a UA888 Interface Module to a U4 receiver.
– 7 – | ENGLISH |
