Safety

2

READ ALL INSTRUCTIONS BEFORE STARTING INSTALLATION

General Safety Information

Electrically powered condensate pumps normally give many years of trouble-free service when correctly installed, maintained, and used. However, unusual cir- cumstances (interruption of power to the pump, algae/debris in the reservoir, electrical or mechanical fail- ure in the pump, etc.), may prevent your pump from functioning normally. Consequently, any condensate pump installed in an area susceptible to water damage must be connected to a failure alarm or water sensing device or include an auxiliary safety shutoff switch acti- vated by high water in the pump reservoir and connect- ed to the thermostat of the furnace/AC unit. See the “Troubleshooting Chart” in this manual for information about common condensate pump problems. For more information, see your dealer or call customer service at 1-800-468-7867.

1.Drain all water from system before servicing.

2.Periodically inspect reservoir, pump, and system com- ponents. Keep free of debris and foreign objects. Perform routine maintenance as required.

3.When installing an electrically driven pump, follow all electrical and safety codes that apply.

4.Make certain power source conforms to requirements of your equipment.

5.Protect electrical cord from sharp objects, hot sur- faces, oil, and chemicals. Avoid kinking cord. Replace or repair damaged or worn cords immediately.

6.Personal Safety:

a.Wear safety glasses at all times when working with pumps.

b.Keep work area clean, uncluttered and properly lighted – replace all unused tools and equipment.

c.Keep visitors at a safe distance from work area.

d.Make workshop child-proof – with padlocks, master switches, and by removing starter keys.

Risk of electric shock. If your basement has water or moisture on floor, do not walk on wet area until all power has been turned off. If shut-off box is in basement, call electric company to shut-off service to house, or call your local fire department for instructions. Failure to follow this warning can result in fatal electrical shock.

When pump is plugged in, do not handle pump, cord, or plug with wet hands or when standing on a wet or damp surface or in water. Unplug pump before servicing it or doing any maintenance on it.

ATTACH ORIGINAL RECEIPT HERE FOR WARRANTY CONSIDERATION.

SIMER warrants to the original consumer purchaser (“Purchaser”) of its products that they are free from defects in material or workmanship.

If within twelve (12) months from the date of the original consumer purchase any such product shall prove to be defective, it shall be repaired or replaced at SIMER’s option, subject to the terms and conditions set forth below. Your original receipt of purchase is required to determine warranty eligibility.

Exceptions to the Twelve (12) Month Warranty

 

 

Product/Model No.

Warranty Period

 

 

 

 

M40P, M40, BW85P, CM10, CMK

90 days

 

 

 

 

2330, 2300, 2310, 2955, 2956, 2957, 2960, A5500, 2520ULST

2 Years

 

 

 

 

4" Submersible Well Pumps, 3984, 3983, 2975PC, 2958, 2985, 3075SS

3 Years

 

 

 

 

Pre-Charge Water System Tank, 3986, 3985, 2956

5 Years

 

 

 

3988, 3995, 3997, 3963

Lifetime

 

 

 

General Terms and Conditions

 

Purchaser must pay all labor and shipping charges necessary to replace product covered by this warranty. This warranty shall not apply to acts of God, nor shall it apply to products which, in the sole judgement of SIMER, have been subject to negligence, abuse, accident, misapplication, tampering, alteration; nor due to improper installation, operation, maintenance or storage; nor to other than normal application, use or service, including but not limited to, operational failures caused by corrosion, rust or other foreign materials in the system, or operation at pressures in excess of recommended maximums.

Requests for service under this warranty shall be made by returning the defective product to the Retail outlet or to SIMER as soon as possible after the discovery of any alleged defect. SIMER will subsequently take corrective action as promptly as reasonably possible. No requests for service under this warranty will be accepted if received more than 30 days after the term of the warranty.

This warranty sets forth SIMER’s sole obligation and purchaser’s exclusive remedy for defective products.

SIMER SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT DAMAGES WHATSOEVER.

THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES. IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT EXTEND BEYOND THE DURATION OF THE APPLICABLE EXPRESS WARRANTIES PROVIDED HEREIN.

Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

SIMER • 293 Wright Street • Delavan, WI U.S.A. 53115

Phone: 1-800-468-7867/1-800-546-7867 • Fax: 1-800-390-5351

E-Mail: info@simerpumps.com • Web Site: http://www.simerpumps.com

For parts or assistance, call Simer Customer Service at 1-800-468-7867 /1-800-546-7867

Page 1 Page 3
Page 2
Image 2
Simer Pumps 2520ULST owner manual General Safety Information, Warranty Period
Page 1 Page 3

2520ULST specifications

The Simer Pumps 2520ULST is a robust submersible pump designed primarily for residential and light commercial applications. Known for its reliability and efficiency, the 2520ULST is engineered to handle a variety of water removal tasks, including sump pumping, drainage, and light sewage applications.

One of the key features of the Simer Pumps 2520ULST is its solid construction. The pump is made with high-quality thermoplastic materials that offer excellent durability and resistance to corrosion, ensuring a long service life even in harsh environments. The lightweight design allows for easy installation and portability, making it an ideal choice for homeowners and contractors alike.

The pump is powered by a powerful 1/2 horsepower motor, capable of moving up to 36 gallons per minute. This impressive flow rate allows the 2520ULST to efficiently handle larger volumes of water, whether it is being used for draining flooded basements or removing water from construction sites. Additionally, the pump has a maximum head of 27 feet, which provides versatility in various applications.

The Simer Pumps 2520ULST incorporates advanced technology with its automatic float switch, which ensures reliable operation without the need for constant monitoring. This feature allows the pump to turn on and off automatically based on water levels, providing peace of mind to users who may not always be present to oversee the operation. The float switch is designed to minimize the risk of clogging or jamming, ensuring smooth and continuous operation.

Another notable characteristic of the Simer Pumps 2520ULST is its ability to handle solids up to 1/2 inch in diameter. This capacity makes it suitable for handling some light sewage or debris, increasing its versatility for various pumping needs. Moreover, the pump features a thermal overload protection system, which shuts down the motor when it overheats, therefore extending its lifespan and preventing potential damage.

For those seeking reliable, efficient, and durable pumping solutions, the Simer Pumps 2520ULST stands out in the market. With its combination of solid construction, high performance, and user-friendly features, this pump is an excellent investment for homeowners and professionals dealing with water removal needs. Whether for routine drainage or emergency situations, the 2520ULST delivers exceptional performance that users can depend on.
Top Page Image Contents