Skil 3380-01 manual Additional Safety Rules, Tool Use, Tool Care

Additional Safety Rules

Tool Use

DON’T FORCE TOOL

It will do the job better and safer at the rate for which it was designed.

USE THE RIGHT TOOL

Don’t force a small tool or attachment to do the job of a heavy duty tool. Don’t used tool for purpose not intended—for example, don’t use a circular saw for cutting tree limbs or logs.

SECURE WORK

Use clamps or a vise to hold work. It’s safer than using your hand and it frees both hands to operate the tool.

NEVER LEAVE TOOL RUNNING UNATTENDED

Turn power off. Don’t leave tool until it comes to a complete stop.

Tool Care

DO NOT ALTER OR MISUSE TOOL

These tools are precision built. Any alteration or modification not specified is misuse and may result in dangerous conditions.

AVOID GASEOUS AREAS

Do not operate electric tools in a gaseous or explosive atmosphere. Motors in these tools normally spark, and may result in a dangerous condition.

MAINTAIN TOOLS WITH CARE

Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and if damaged, have repaired by authorized service facility. Inspect extension cords periodically and replace if damaged. Keep handles dry, clean and free from oil and grease.

!Before connecting the tool to a power source (receptacle, outlet, etc.), be sure voltageWARNINGsupplied is the same as that specified on the nameplate of the tool. A power source with a voltage greater than that specified for the tool can result in serious injury to the user, as well as damage to the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with a voltage less than the nameplate

rating is harmful to the motor.

3.

!				For your own safety, do not operate your
		WARNING		grinder until it is completely assembled
and installed			according to the instructions … and until
you have read and understood the following:
1.		Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–4
2.		Motor Specifications . . . . . . . . . . . . . . . . . . . . . . 5
3.		Getting To Know Your Grinder . . . . . . . . . . . . . 8
4.		Assembly and Adjustments . . . . . . . . . . . . 9–11
5.		Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 12–13
7.		Maintaining Your Grinder . . . . . . . . . . . . . . . . . 14
8.		STABILITY OF THE BENCH GRINDER
If there is any tendency of the bench grinder to tilt or
move during any use, bolt it to the bench top or to a
piece of 3/4" exterior plywood large enough to stabilize
the grinder. Bolt the plywood to the underside of the
base so it extends beyond the sides of the base. DO
NOT USE PRESSED WOODS PANELS. They can
break unexpectedly. If the workpiece is too large to
easily support with one hand, provide an auxiliary
support.
				Risk of injury due to accidental
!		WARNING
				starting. Do not use in an area where
children may be present.
9.		LOCATION
Use the grinder in a well lit area and on a level surface,
clean and smooth enough to reduce the risk of trips and
falls. Use it where neither the operator nor the casual
observer is forced to stand in line with a potential
kickback.
10. PROTECTION: Eyes, hands, ears and body.
				TO AVOID BEING PULLED INTO
	!	WARNING
				THE SPINNING TOOL—
DO NOT WEAR: Loose fitting gloves
				Necktie
				Loose clothing
				Jewelry
DO: TIE BACK LONG HAIR
a.		ROLL LONG SLEEVES ABOVE ELBOWS
		If any part of your grinder is missing, malfunctioning,
has been damaged or broken … such as the motor
switch, or other operating control, a safety device or the
power cord … cease operating immediately until the
particular part is properly repaired or replaced.
b.		If you are not completely familiar with operating a

grinder, consult your instructor, supervisor or other qualified individual.