OPEN /
CLOSE

Universal Garage Door

 

Remote Control

Model G6VR

1. INTRODUCTION

 

Congratulations on your purchase of the Skylink® G6VR Universal Garage Door Remote Control. This is a kit with a universal remote control and Smart ButtonTM. Simply replace the traditional wall button by the Smart ButtonTM, that’s all for the installation. In this kit, you will find the following:

 

 

Visor clip

2 Wire

 

 

 

 

 

 

Connectors

Universal

Smart ButtonTM

Mounting

 

Remote Control

 

Accessories

 

(Battery included)

 

 

 

 

 

 

2. INSTALLATION

 

Unplug the power cord of your garage door opener

WARNING

before installation to ensure power is not connected.

 

GTR Smart ButtonTM

The GTR Smart ButtonTM replaces most garage door “push buttons” or “wall consoles”. There are 2 different kinds of “push buttons”.

1) Single button

2) Multi-Function Wall Console

1) Single button

If your garage door opener comes equipped with a single button “push button”, you can replace the existing push button with Skylink® Smart ButtonTM GTR. Please follow the procedures below.

2. INSTALLATION (CONT)

If you have the multi-function wall console, do not replace the wall console by the Smart ButtonTM. You need to install the Smart ButtonTM in parallel with your existing wall console.

1. Remove the existing wall console from the wall by removing the screws.

2. Remove the 2 screws that secure the wires on the wall console.

3. Connect the wires from the Smart ButtonTM to the existing wall console. Polarity does not matter,

so simply pick one wire from the Smart ButtonTM, and connect it to one of the terminals on the

existing wall console. Do the same for the 2nd

wire. 4. After connecting the wires, mount the Smart

ButtonTM on to the wall with 2 screws. Also mount the original wall console on to the wall.

5. Plug in the AC cord of the garage door opener. The red light on the Smart ButtonTM should flash 15 seconds after plugging in the power. The red light will not flash immediately after plugging in

the power, which is normal. The Smart ButtonTM is now ready to be operated.

6.If the Smart ButtonTM red light does not flash at all 2 minutes after plugging in the AC cord, your

garage door opener is probably too old. However, the Smart ButtonTM will still work by plugging in an adapter (purchase separately). Please contact Skylink® to purchase the adapter.

Rating of the transformer: 12V DC, 100mA

Diameter of DC plug : 3.5mm

Note: Straighten up the antenna to improve signal reception.

1.Remove the existing push button by removing the screws.

2. Disconnect the 2 wires that are connected to the existing push button.

3. Connect the 2 wires from the existing wall button to the GTR Smart ButtonTM. Twist the 2 wires together with the wire connector

provided. Polarity does not matter, so simply pick one wire from the existing wall button, and

connect it to one of the wires on the Smart

ButtonTM. Do the same for the 2nd wire. 4. After connecting the wires, mount the Smart

ButtonTM on to the wall with 2 screws.

5. Plug in the AC cord of the garage door opener. The red light on the Smart ButtonTM should flash 15 seconds after plugging in the power. The

red light will not flash immediately after plugging in the power, which is normal. The

Smart ButtonTM is now ready to be operated.

Remove existing wires

Antenna

3. OPERATION

If the red light on the Smart ButtonTM is flashing slowly, that indicates it is in standby mode. When a valid remote control signal is received, it will open / close the garage door.

Simply press the button on the remote control or Smart ButtonTM, it will open / close the garage door.

Programming

Learn additional remote controls

Smart ButtonTM can learn up to 15 remote controls. To learn additional remote controls, follow the instructions below:

1.Press the learn button on the side of the GTR.

2.Once the learn button is pressed, the LED will

flash quickly. You may release the learn button.

Note: Straighten up the antenna to improve signal reception.

2) Multi-Function Wall Console

Multi-Function Wall Console normally comes with 3 buttons that can be used to:

1) operate the garage door opener lighting, 2) lock the receiver so it doesn’t accept remote control operation, and

3) push button for door opening / closing

3. Press the button on the remote control you would like to program.

4. Once the remote control is programmed, the LED

will flash slowly, in the same way as it flashes

Learn

Button

in standby mode.

 

5.You may now operate the garage door opener with this new remote control.

Page 1
Image 1
SkyLink manual Model G6VR, GTR Smart ButtonTM, Programming

G6VR specifications

The SkyLink G6VR is a cutting-edge virtual reality headset that has garnered attention for its advanced features and immersive technology. Designed for both casual users and gaming enthusiasts, the G6VR aims to bring virtual experiences to life with impressive clarity and responsiveness.

One of the standout features of the SkyLink G6VR is its high-resolution display. With a dual-panel setup that offers a combined resolution of 4K, users can enjoy crystal-clear visuals at a high refresh rate. This ensures that fast-paced games and dynamic environments are rendered smoothly, minimizing motion blur and providing a more lifelike experience. The headset also boasts a wide field of view, allowing users to fully immerse themselves in their virtual environments.

In terms of tracking technology, the G6VR employs an advanced inside-out tracking system. This allows for precise motion detection without the need for external sensors, giving users the freedom to move around their physical space while still interacting with virtual elements. The headset features multiple cameras strategically placed around it, ensuring accurate tracking in a variety of lighting conditions.

Comfort is also a key aspect of the G6VR's design. The headset is lightweight and ergonomically shaped to reduce strain during extended wear. Padded components and adjustable straps ensure a snug fit, allowing users to focus on their virtual experiences without discomfort.

For enhanced immersion, the G6VR comes equipped with spatial audio technology. Integrated speakers provide a three-dimensional sound experience, allowing users to hear sounds as they would in real life, whether it be the rustle of leaves in a game or the distant sounds of a virtual city. Additionally, the headset supports haptic feedback for compatible applications, providing tactile sensations that further enrich the gaming experience.

Connectivity is another strong suit of the SkyLink G6VR. It supports both wired and wireless connections, allowing users to choose their preferred setup. The wireless mode provides a level of freedom that lets users move without being tethered to a PC or console, although the wireless experience maintains a minimal latency for seamless interaction.

Finally, the G6VR is designed with versatility in mind. It supports a wide range of applications, from gaming to educational content and virtual simulations, making it suitable for various users. The ecosystem of VR content available ensures that both newcomers and seasoned VR veterans can find something to enjoy.

In conclusion, the SkyLink G6VR stands out with its high-resolution displays, advanced tracking systems, comfort features, and immersive audio technology. Whether for gaming, education, or training purposes, the G6VR represents a significant advancement in the realm of virtual reality headsets, delivering an engaging experience for users of all types.