SkyLink ID-318 Installation, Erasing Motion Sensor from Receivers, Battery, Warranty, Accessories

3. CUSTOMIZING THE MOTION SENSOR (CONT)

If the jumper connector is in place, the light sensor threshold is set to dark, a motion activation signal will not turn on the lighting receiver unless the environment is really dark.

If the jumper connector is removed, the light sensor threshold is set to dim, a motion activation signal will turn on the lighting receiver even the environment is not so dark.

You should set the desired light sensing threshold by trial and error.

After setting all the jumper connectors, you may place the battery com- partment door back on and tighten the screw. You may now mount the motion sensor at the desired location where movement will be monitored.

4. INSTALLATION

You can use the mounting accessories to mount the Motion Sensor on a wall. First, mount the ball joint on the wall, then slide the Motion Sensor on the ball joint. You should mount it at a height of about 7ft from the ground to achieve better coverage.

7ft

6. ERASING MOTION SENSOR FROM RECEIVERS

Erasing Motion Sensor from the Dimmable Receiver Module model MD-318 or On / Off Receiver Module model MR-318

You may erase a transmitter from the receiver module, but you cannot erase a specific device directly, you must erase all the wireless devices, then program the ones you want to keep. Follow the instructions below to erase programmed transmitters.

1.Power off the receiver module.

2.Press the SET button on the Motion Sensor.

3.Press and hold the SET button for at least 2 seconds. Do not release this button until step 5.

4.Power up the receiver module, you will hear a beep.

5.You may release the SET button.

6.When the button is release, you have successfully erased all the devices from the lighting receiver.

To erase Motion Sensor from other receivers, please refer to the instructions of the receivers.

7. BATTERY

When the LED does not flash (ON then OFF, etc) after the Motion Sensor is triggered or when the motion sensor does not control receiver after movement is detected, it is time to replace the battery. Refer to Section 2 to open the battery door.

Note: Dispose of batteries properly.

8. FCC

The Remote Control is approved by the FCC and it complies with Part 15 of the FCC Rules. Its operation is subject to the following two conditions :

1.This device may not cause harmful interference.

2.This device must accept any interference that may cause undesired operation.

WARNING:

Changes or modifications to this unit not expressly approved by the party responsible of compliance could void the user’s authority to operate the equipment.

9. WARRANTY

If, within one year from date of purchase, this product should become defective (except battery), due to faulty workmanship or materials, it will be repaired or replaced, without charge. Proof of purchase and a Return Authorization are required.

5. TESTING AND OPERATION

Walk Test

Walk test should be performed after the motion sensor is mounted. Walk in the covered area, if motion is detected, a red light inside the sensor will flash. If the red light does not flash, motion has not been detected and you may need to re-position the sensor. Ensure you walk test the whole area that you would like the motion sensor to cover.

Note:	DETECTING AREA:		(Unit = meter)
- Perform the walk test after you	10	55°	1.2M	55°
have inserted the battery for more				11°
	8
than 1 minute.	6
- The sensor will not be triggered	4	22°	27°	22°
by a new motion unless no motion
	2
has been detected for 3 seconds.	M
Therefore, wait for at least 3 seconds
during walk testing to make a next		12°
movement.
- Disable CDS Light Sensor during	SENSOR
walk test, re-enable it after walk test.

0 1 2 3 4 5 6 7 8 9 10

10. CUSTOMER SERVICE

If you would like to

-find out the up-to-date specifications

-know more about features and applications

-download documents, i.e. user’s instructions

-order Skylink products

or if you have difficulty getting products to work, please:

1.visit our FAQ section at www.skylinkhome.com, or

2.email us at support@skylinkhome.com, or

3.call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST. Fax (800) 286-1320

11. ACCESSORIES

The SkylinkHomeTM System consists of many other devices such as SkylinkPadTM Remotes, Motion Sensor, ON/OFF Wall Switch, Wall Dimmer, Plug-In Dimmer with or without Repeater, Plug-In ON/OFF Control (Outdoor/Indoor), Screw-In Dimmer, ON/OFF/Dimming Control, ON/OFF Control, Smart ButtonTM Garage Door Control, etc. Please visit Skylink website at www.skylinkhome.com for more information.

Note:

When installing the motion sensor, avoid placing it near heat or cold producing devices (i.e. A/C or furnace vents, fans, ovens, space heaters, etc), and avoid pointing it to the moving objects like a window curtain. Air movement, especially caused by changes in temperature may trigger the Motion Sensor. Please carefully test your Motion Sensor so that it will only be triggered by wanted movement.

CUSTOMER SERVICE

17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3 Email:support@skylinkhome.com http://www.skylinkhome.com

P/N. 101Z702	V2.0
Patent Pending

©2010 SKYLINK GROUP