SkyLink LK-318-3 manual Introduction, Power UP, Programming Transmitters to Receiver Module

1-Button Remote	Model LK-318-1
2-Button Remote	Model LK-318-2
3-Button Remote	Model LK-318-3
	1. INTRODUCTION

Thank you for your purchase of a SkylinkHomeTM Remote, Model LK- 318-1/ LK-318-2 / LK-318-3. This remote which is also called transmitter in this document allows you to wirelessly operate SkylinkHomeTM receiver modules.

All wireless signal communications within the SkylinkHomeTM system are based on rolling code technology to ensure highest security is used.

The following items are included in this package:

-One of LK Series Remotes

-Lithium Battery CR-2032 (Installed)

-User’s Instructions

Red

LED

Buttons

1-Button	2-Button	3-Button
Transmitter	Transmitter	Transmitter
LK-318-1	LK-318-2	LK-318-3

2. POWER UP

To power the transmitter, simply remove the battery isolator from the transmitter, red LED will flash once. Press the button on the transmitter, the red LED should flash. The transmitter is now powered properly. If the red LED does not flash when button is pressed, refer to Section 6 “Battery” of this manual.

1)	Remove isolator,	LED on for
		1 second
2)	LED on for 1 second

Remove isolator

3. PROGRAMMING TRANSMITTERS TO RECEIVER MODULE

In order to operate the receiver module remotely with a transmitter, it must be programmed to the receiver module.

To program a remote to the receiver module, a “Learn” code must be transmitted, follow the instructions below to transmit the “Learn” code to the receiver.

1.Put the receiver module that you plan to program into programming mode. Refer to the User’s Instructions of that receiver module.

2.Press 1 and 2 simultaneously and hold for 2 seconds until the LED changes from on to flashing quickly. Release the buttons. The red

LED on the transmitter will be on for 15 seconds.

3.Press the button on the remote that you plan to use when the LED is steadily on to transmit the “Learn” code.

4.Once the remote is programmed, the receiver modules will quit from programming mode and the programmed transmitter is ready to be used now.

Learn Code

Follow steps 2 and 3 above to transmit the “Learn” code when programming the remote to receiver modules.

You may follow the same instructions to program different buttons on the transmitter to different receiver modules.

4. ON / OFF OPERATION

Pressing the programmed button on the transmitter once will toggle the status of the load that is connected to the receiver module, i.e. if the light is off, pressing the button turns on the light, and vice versa.

When the programmed button is pressed, the red LED flashes briefly indicating signal is transmitting.

5. ADVANCED FEATURE - PASSWORD PROTECTION

Password protection (Only available for LK-318-3 (Not available for LK-318-1 or LK-318-2)

The LK-318-3 can be password protected. If you enable the password protection, you can only operate LK-318-3 after you input the correct password.

Password can be 2-8 digits long, which is a combination of 1, 2 and 3. For example, password can be 1, 2, 1, 2. To input this password, you have to press button [1], then [2], then [1], then [2].

Note:

[1] = Button 1 [2] = Button 2 [3] = Button 3

Button [1]

Button [2]

Button [3]

Note:

The time-out period is 1 second during above password input.

The factory default password is 2, 2, 2, and this password function is disabled out of factory.

Change password

1.Press 1 and 3 simultaneously and hold for more than 10 seconds until the LED changes from flashing quickly to flashing slowly.

2.Input old password.

3.Press 1 and 3 once simultaneously to confirm. If the password is wrong, the LED will flash 3 times and you have to start it over from step1.

4.Input new password.

5.Press 1 and 3 once simultaneously to confirm.

6.Input new password again.

7.Press 1 and 3 once simultaneously to RE-confirm. If the password is different from the one of step 4, the LED will flash 3 times and you have to start over from step 1. Otherwise, the password has been changed to the new one and the password protection is enabled.

Disable password

1.Press 1 and 3 simultaneously and hold for more than 5 seconds until the LED flashes quickly but not until the LED flashes slowly.

2.Input old password.

3.Press 1 and 3 once simultaneously to confirm. If the password is the password protection will be disabled.

Enable password

1.Press 1 and 3 simultaneously and hold for more than 2 seconds until the LED flashes quickly but not until the LED flashes slowly.

2.Input old password.

3.Press 1 and 3 once simultaneously to confirm. If the password is correct, the password protection will be enabled.

You can toggle the two states - password protection enabled or disabled.

Note:

The time-out period is 15 seconds during any of the above setting opera- tions. After 10 seconds, the LED will flash 3 times and the remote will exit from setting.