SkyLink MD-318 Erasing Transmitters from the ON/OFF/DIMMING Control, Technical Specifications

5. OPERATION (CONT)

In case the transmitter is not on hand, you can still operate the lighting fixture with the wall switch.

This receiver offers two optional states after powered on, choose the one which fits your requirement.

1. Power On - Light On:

1)You may use the wall switch to control the light as usual. When the wall switch is off, the light is off. When the wall switch is on, the light is on.

2)After a power outage and the electricity comes back, the light will be on if the wall switch is in On position.

2. Power On - Light Off:

1)A special sequence is needed to turn on the light by the wall switch. To turn on the light by the wall switch: 1) Switch On, 2) Switch Off, 3) Switch On again within 2 seconds. Light will be on.

2)After a power outage and electricity comes back, the light will be off under most of the circumstances.

To toggle a receiver between these two states, re-program a transmitter twice consecutively to the receiver. Referring to Section 3, repeat the programming steps twice consecutively with a transmitter that is already programmed, the receiver will change state.

6.ERASING TRANSMITTERS FROM THE ON/OFF/DIMMING CONTROL

You may erase a transmitter from the ON/OFF/Dimming Control, but you cannot erase a specific device directly, you must erase all the wireless devices, then program the ones you want to keep. Follow the instructions below to erase programmed transmitters.

1.Power off the lighting receiver. (Switch off the wall switch)

2.Transmit a "Erase" code from the transmitter until step 4.

3.Power up the ON/OFF/Dimming Control (Switch on the wall switch), you will hear a beep.

4.You may stop the "Erase" code signal transmission, the ON/OFF/ Dimming Control will beep, indicating you have successfully erased all the devices from the ON/OFF/Dimming Control.

To erase other transmitters / sensors, please refer to the instructions of the transmitters / sensors.

7. TECHNICAL SPECIFICATIONS

Input Voltage: 120VAC , 60Hz

Standby Current: 6mA

Minimum Load: 10W

Maximum Load: 300W at 120VAC

Operating Frequency: 318MHz

Operational Temperature: -4° F - 140° F (-20° C - 60° C)

Humidity: 5%-95%

Range: Up to 500 feet in open area

CUSTOMER SERVICE

17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3 Email:support@skylinkhome.com http://www.skylinkhome.com

P/N. 101Z699

Patent Pending

©2010 SKYLINK GROUP

8. FCC

The Remote Control is approved by the FCC and it complies with Part 15 of the FCC Rules. Its operation is subject to the following two conditions :

1.This device may not cause harmful interference.

2.This device must accept any interference that may cause undesired operation.

WARNING:

Changes or modifications to this unit not expressly approved by the party responsible of compliance could void the user’s authority to operate the equipment.

9. WARRANTY

If, within one year from date of purchase, this product should become defective (except battery), due to faulty workmanship or materials, it will be repaired or replaced, without charge. Proof of purchase and a Return Authorization are required.

10. CUSTOMER SERVICE

If you would like to

∙find out the up-to-date specifications

∙know more about features and applications

∙download documents, i.e. user’s instructions

∙order Skylink products

or if you have difficulty getting products to work, please:

1.visit our FAQ section at www.skylinkhome.com, or

2.email us at support@skylinkhome.com, or

3.call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST. Fax (800) 286-1320

11. ACCESSORIES

The SkylinkHomeTM System consists of many other devices such as SkylinkHomeTM Remotes, Motion Sensor, ON/OFF Wall Switch, Wall Dimmer, Plug-In Dimmer with or without Repeater, Plug-In ON/OFF Control (Outdoor/Indoor), Screw-In Dimmer, ON/OFF/Dimming Control, ON/OFF Control, Smart ButtonTM Garage Door Control, etc. Please visit Skylink website at www.skylinkhome.com for more information.