Door/Window Sensor | Model |
1. INTRODUCTION
The Door / Window Sensor is designed to monitor any door or window within your house. It works in conjunction with MA Series Control Panel. When the monitored window or door is opened, the control panel will either alert you or alarm will be triggered.
In this package, you should find a sensor, a magnet, 3V lithium battery and other mounting accessories.
2. LEARN SENSOR TO MA SERIES CONTROL PANEL (CONT)
Test Sensor
After learning the sensor to the control panel, you may test the com- munication by placing the magnet beside the transmitter (where the red marking is) and remove the magnet from the transmitter.
Magnet
Sensor
|
| 3V Lithium |
|
| battery |
2 pcs | 3.5 x 18 screws | Mounting plate |
2 pcs | 3.5 x 12 screws |
|
When the magnetic contact is closed, the | When the magnetic contact is broken (open), |
receiver will not beep. | the receiver will beep and a LED will flash. |
Please follow the instructions below to set up the door / window sensor.
2. LEARN SENSOR TO MA SERIES CONTROL PANEL
In order for the sensor to communicate with the control panel properly, the sensor must be programmed to the control panel. Follow the brief instructions below or refer to the detail instructions from the MA Series User’s Instructions to program the sensor to the control panel. Before proceeding, please remove the battery isolator from the sensor, and placing the magnet beside the transmitter (where the red marking is)
Step 1:
Press and hold the Learn Button on the Control Panel for 3 seconds. Control Panel beeps once and you may release the Learn Button.
12V |
|
| |
DC |
|
| |
INPUT |
|
| |
MUTE |
|
| |
LEARN | Press 3 sec. | Long Beep | |
ALERT | |||
|
| ||
CHIME |
|
| |
OFF |
|
|
Step 2:
Press the zone button (1, 2, 3, or 4) once, for which you want to program the sensor to. The selected Zone LED will flash.
Press the zone button Zone LED flashing
Step 3:
Activate the Door Window Sensor by separating the magnet from the sensor unit.
1)Zone LED of this sensor will flash
2)Beeping according to the zone number [Alert Notification Switch is set to "Alert"]. 1 beep for zone 1, 2 beeps for zone 2 etc, until the sensor is closed.
Note: If the Alert Notification Switch is set to "Chime", Control Panel will chime once for every signal activation. If the Alert Notification Switch is set to "OFF", no audio alert will sound.
3. INSTALLATION
The transmitters should be mounted on the door frame or window frame by double sided tape. The magnet should be mounted on the door or window by either double sided tape or screws. Make sure the magnet is aligned with the red marking on the transmitter. If the surface of the frame is flat enough,
| Magnet | "Red Marking" | Magnet |
"Red Marking" | on the side | ||
on the side | Sensor | Sensor |
|
|
|
MagnetSensor
Separate the magnet from
Control Panel long beep
Mounting plate | Sensor |
the sensor.
Step 4:
Zone LED flashing OFF
and screws (optional) foam tape |
Testing:
After mounting the sensor, test the sensor by opening and closing the door or window. The Control Panel should respond in the same way as described above, "Test Sensor".
You will hear a long beep and the zone LED stops flashing. The sensor is now programmed to the Control Panel.
Note:
Note:
-Try to mount the sensors as far away from the floor as possible to avoid damaging them. Mounting the sensors at a higher position will also result in better operating range.
You may program up to 4 sensors to one zone.
Zone 4 is an alert zone, sensors in this zone is for alert purpose ONLY and will not trigger the alarm.
-Do not mount the sensor to the exterior of the door / window, always mount the sensor to the interior side of the door / window to avoid being damaged or stolen by