Connecting to a Power Source | SMC Networks SMCBGLLCX1, SMCRPS600W*

INSTALLING THE SWITCH

Connecting to a Power Source

To connect a device to a power source:

1.Insert the power cable plug directly into the receptacle located at the back of the device.

Figure 3-4. Power Receptacle

2. Plug the other end of the cable into a grounded, 3-pin socket.

Note: For International use, you may need to change the AC line cord. You must use a line cord set that has been approved for the receptacle type in your country.

3.Check the front-panel LEDs as the device is powered on to be sure the Power LED is lit. If not, check that the power cable is correctly plugged in.

4.If you have purchased a Redundant Power Unit, connect it to the device and to an AC power source now, following the instructions included with the package.

3-6

Image 44

SMC Networks SMCBGLLCX1, SMCRPS600W*, SMCBGSLCX1 manual Connecting to a Power Source, Power Receptacle

Contents

TigerSwitch 10/100 Page TigerSwitch 10/100 Installation Guide Trademarks Limited Warranty Limited Warranty Compliances FCC Class aEC Conformance Declaration Class a Iii Compliances Industry Canada Class a Underwriters Laboratories Compliance Statement Safety ComplianceWarnhinweis Faseroptikanschlüsse Optische Sicherheit Vii Wichtige Sicherheitshinweise Germany Viii Contents Installing the Switch Making Network Connections Contents Xii Chapter About Tigerswitch 10/100 Overview Management Options Switch ArchitectureSwitching Method Spanning Tree Protocol VLANs Multicast Switching Traffic Priority 1000BASE-T/SFP Ports Description of Hardware10BASE-T/100BASE-TX Ports Status LEDs Port and System LEDs System Status LEDs Optional Redundant Power Unit Power Supply Receptacles Features and Benefits Connectivity Performance Management About the Tigerswitch 10/100 Introduction to Switching Chapter Network Planning Sample Applications Collapsed Backbone Central Wiring Closet Central Wiring Closet Collapsed Backbone Using Fiber Cable Remote Connections with Fiber Cable Making Vlan Connections Making Vlan Connections Connectivity Rules Mbps Gigabit Ethernet Collision Domain Mbps Fast Ethernet Collision Domain Maximum Fast Ethernet Cable DistanceSMC 3-2 Rule for Class II Repeaters SMC 2-1 Rule for Class I Repeaters Maximum Network Diameter Using Repeaters Mbps Ethernet Collision DomainMaximum Ethernet Cable Distance SMC 5-4-3 Rule Application Notes Network Planning Installing the Switch Selecting a Site Optional Rack-Mounting Equipment Equipment ChecklistPackage Contents Mounting Rack Mounting Attaching the Brackets Desktop or Shelf Mounting Attaching the Adhesive Feet Connecting to a Power Source Power Receptacle Connecting Network Devices Chapter Making Network ConnectionsTwisted-Pair Devices Cabling Guidelines Connecting to PCs, Servers, Hubs and Switches Making Twisted-Pair Connections Wiring Closet Connections Wiring Closet Connections Making Network Connections Power and Cooling Problems Appendix a TroubleshootingDiagnosing Switch Indicators Installation In-Band Access Specifications Appendix B Cables Figure B-1. RJ-45 Connector Pin Numbers Twisted-Pair Cable and Pin Assignments 100BASE-TX/10BASE-T Pin Assignments RJ-45 Pin Assignments Pin MDI Signal Name MDI-X Signal Name 1000BASE-T Pin Assignments 1000BASE-T Cable Requirements Cable Testing for Existing Category 5 CableAdjusting Existing Category 5 Cabling to Run 1000BASE-T Console Port to 9-Pin COM Port on PC Console Port Pin AssignmentsDB-9 Port Pin Assignments Console Port to 25-Pin DTE Port on PC Cables Appendix C Specifications Physical Characteristics Temperature Power SupplyPower Consumption Humidity Switch Features Management Features Standards Warranty SafetyCompliances CE Mark Emissions Specifications Appendix D Ordering Information Ordering Information Glossary Glossary-11000BASE-T Auto-Negotiation Glossary-2 Glossary-3 Glossary-4 Virtual LAN Vlan Glossary-5Transmission Control Protocol/Internet Protocol TCP/IP Glossary-6 Index Index-1 Index-2 Index-3 Index-4 Page For Technical SUPPORT, Call