Section 2 - OPERATING INSTRUCTIONS

2.1PRE-START CHECK LIST

Make the following checks and perform the service required before each start-up.

2.1.1.Check engine oil and add oil as needed to bring level up to the FULL mark. Refer to engine owner's manual for oil specifications

2.1.2.Check guards, chutes, deflectors and covers to make sure all are in place and securely tightened.

2.1.3.Check auger control and wheel drive control to insure cables are connected and both levers

operate freely. See Figure 2.1.

IMPORTANT: On 7 HP models only. Standing in the operator's position, the left handle bar lever is for wheel drive engagement and disengagement. The right handle bar lever is for auger/impeller engagement and disengagement. Hold both levers down to handle bar for engagement and release levers for disengagement.

When both levers are pressed down to the handle bar at the same time, the operator can release the right hand lever and the right lever will remain engaged as long as the left hand lever is held down to handle bar. Release the left hand lever and both levers will disengage.

2.1.6.Add fuel to tank after pushing the machine outside where fumes can safely dissipate. Make sure cap is tightened after refueling. Wipe up any spilled fuel on machine and surrounding area. Refer to Engine Owners Manual for specifications.

2.1.7.Check auger housing and discharge chute, both must be free of all obstructions. Clean engine of any accumulation of spilled fuel, dirt, etc.

,WARNING

DO NOT use an electrical extension cord that is damaged. A damaged electrical extension cord could cause a shock or fire. Thoroughly inspect electrical extension cord before using machine. If cord is damaged, do not use and do not operate machine. Replace damaged cord immediately. Contact your Snapper service dealer for assistance. To reduce the risk of electric shock, use only with an extension cord intended for outdoor use having a cord type:

SW-A, SOW-A,STW-A, STOW-A,SJW-A, SJTW-A or SJTOW-A.

AUGER/IMPELLER

_HEEL DRIVE

CONTROL

CONTROL _

*/

t4Q

FIGURE 2.1

2.1.4.Check chute operation. Rotate chute crank to insure smooth rotation throughout its range.

2.1.5.Check tires and add or release air as needed to bring air pressure to 12 psi without tire chains. Air pressure with tire chains should be 16 psi.

WARNING

Use approved fuel container. DO NOT smoke near open fuel container. DO NOT fill fuel tank indoors or when engine is running. Allow engine to cool for at least ten minutes before refilling. Wipe off any spilled fuel before starting engine. DO NOT run engine indoors.

IMPORTANT: Electric Start Kit optional accessory on some models.

2.1.8.Check and make sure extension cord is in good condition. Extension cord should not have any broken insulation or exposed wires. Use an extension cord that is heavy enough to carry the correct amount of current to the machine. See

Figure 2.2 for correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge cord.

MINIMUM GAUGE FOR CORD SETS

120 or 230 Volt

Total

Length

of Cord in Feet

Rating-Amps

25 ft. I

50 ft.

I 100 ft. I 150 ft.

More

Not More

 

,7,.,,,.,A.W.('_.

 

Than

Than

 

 

 

 

0

6

18

16

16

14

6

10

18

16

14

12

10

12

16

16

14

12

12

16

14

12

Not

 

 

 

 

 

Recommended

 

 

FIGURE

2.2

 

 

Page 25
Image 25
Snapper 155223 important safety instructions T4Q

155223 specifications

The Snapper 155223 is a highly regarded machine in the realm of outdoor power equipment, particularly recognized for its robust performance and innovative features. Designed for homeowners seeking an efficient lawn mowing solution, the Snapper 155223 combines power, durability, and user-friendly functionality.

One of the standout features of the Snapper 155223 is its 22-inch steel mowing deck. This deck provides a wide cutting area, allowing users to cover larger sections of lawn in less time. The durable steel construction ensures longevity, resisting the wear and tear that often comes from regular use. Additionally, the mowing deck is designed for a clean and precise cut, promoting healthy grass growth.

The Snapper 155223 is powered by a reliable Briggs & Stratton engine, specifically engineered to deliver consistent power and performance. This 190cc engine not only offers ample horsepower but also integrates fuel-efficient technology, making it an economical choice for lawn care. The engine's easy-start feature simplifies the startup process, allowing users to get to work quickly.

Tech-savvy advancements are evident in the Snapper 155223 as well. It features a variable speed self-propelled drive system that allows users to adjust the pace of the mower according to their comfort and the terrain's conditions. This adaptability is particularly beneficial when maneuvering around obstacles or tackling uneven ground.

The Snapper 155223 also emphasizes user comfort and convenience. Its ergonomic handle design minimizes fatigue during extended use, while the adjustable cutting height provides flexibility for different grass types and seasonal growth conditions. Users can select from multiple height settings to achieve the perfect cut.

Furthermore, maintenance is made easy with the Snapper 155223. The mower includes a rear discharge option and is compatible with mulching capabilities, allowing users the flexibility to choose how they want to manage grass clippings. The integrated washout port simplifies cleaning the mowing deck, enhancing the overall maintenance experience.

In summary, the Snapper 155223 stands out as a versatile and durable lawn mower, packed with features that cater to the needs of the modern homeowner. Its powerful engine, robust cutting deck, and user-friendly technologies make it an excellent choice for anyone looking to maintain a beautiful lawn efficiently and effectively.