Troubleshooting
| PROBLEM | PROBABLE CAUSE | CORRECTIVE ACTION | ||
|
|
|
|
|
|
| Engine Will Not | 1. | Fuel tank empty. | 1. | Fill fuel tank with fresh fuel to proper level. |
| Start Using |
|
|
|
|
| 2. | Engine needs choking. | 2. | Move choke control to “CHOKE” position. | |
| Recoil Starter |
|
|
|
|
| 3. | Spark plug wire disconnected. | 3. | Place spark plug wire onto spark plug. | |
|
| ||||
|
|
|
|
|
|
|
| 4. | Faulty parking brake, blade or ignition switch. | 4. | Contact authorized SNAPPER dealer. |
|
|
|
|
|
|
|
| 5. | Park brake not engaged. | 5. | Engage park brake. |
|
|
|
|
|
|
|
| 6. | Ignition is in the OFF position. | 6. | Turn ignition switch to the RUN position. |
|
|
|
|
|
|
| Engine Will Not | 1. | Fuel tank empty. | 1. | Fill fuel tank with fresh fuel to proper level. |
| Start Using |
|
|
|
|
| 2. | Engine needs choking. | 2. | Move choke control to “CHOKE” position. | |
| Electric Starter |
|
|
|
|
| 3. | Spark plug wire disconnected. | 3. | Place spark plug wire onto spark plug. | |
|
|
|
|
|
|
|
| 4. | Faulty parking brake, blade or ignition switch. | 4. | Contact authorized SNAPPER dealer. |
|
|
|
|
|
|
|
| 5. | Park brake not engaged. | 5. | Engage park brake. |
|
|
|
|
|
|
|
| 6. | Blown Fuse. | 6. | Replace with new 20 AMP fuse. |
|
|
|
|
|
|
|
| 7. | Faulty interlock module. | 7. | Contact authorized SNAPPER dealer. |
|
|
|
|
|
|
|
| 8. | Ignition is in the OFF position. | 8. | Turn ignition switch to the START position. |
|
|
|
|
| |
|
| 9.Battery is weak or dead. | 9. | Charge or replace with new battery. | |
|
|
|
| ||
|
| 10. Battery cables loose, broken disconnected or | 10. Clean and connect battery cables. If broken, replace | ||
|
| corroded. | with new battery cables. | ||
|
|
|
| ||
|
| 11. Faulty electric starter or starter solenoid. | 11. Contact authorized SNAPPER dealer. | ||
|
|
|
| ||
|
| 12. Starter cable loose, broken or disconnected. | 12. Connect starter cable. If broken, replace with new | ||
|
|
|
| starter cable. | |
|
|
|
| ||
|
| 13. Electrical wiring harness disconnected or | 13. Connect or replace with new wiring harness. | ||
|
| broken. |
|
| |
|
|
|
|
|
|
| Engine Stalls | 1. | Operator not in seat. | 1. | Sit in operator’s seat. |
| After Running |
|
|
|
|
| 2. | Choke control in the “CHOKE” position. | 2. | Move choke control to “OFF” position. | |
|
|
|
|
|
|
|
| 3. | Fuel tank empty. | 3. | Fill fuel tank with fresh fuel to proper level. |
|
|
|
|
|
|
|
| 4. | Engine air | 4. | Clean free of all debris. |
|
|
|
|
|
|
|
| 5. | Spark plug defective or gap set improperly. | 5. | Service spark plug. |
|
|
|
|
|
|
|
| 6. | Fuel filter restricted. | 6. | Replace fuel filter. |
|
|
|
|
|
|
|
| 7. | Water, debris or stale fuel in fuel system. | 7. | Drain and clean fuel system. |
|
|
|
|
|
|
| Engine Loses | 1. | Excessive load on engine. | 1. | Lessen load. |
| Power |
|
|
|
|
| 2. | Engine air | 2. | Clean or replace filters. | |
|
|
|
|
|
|
Troubleshooting |
| 3. | Spark plug faulty. | 3. | Service spark plug. |
|
|
|
|
| |
|
| 4. | Water, debris or stale fuel in fuel system. | 4. | Drain and clean fuel system. Replace filter. |
|
|
|
|
|
|
|
| 5. | Debris build up on engine cooling screen. | 5. | Clean all debris from engine cooling screen. |
|
|
|
|
|
|
| Engine Backfires | 1. | Throttle control set too “FAST”. | 1. | Set throttle control to “SLOW” and allow engine to idle. |
| When Turned To |
|
| Then, turn key to “OFF”. | |
| “STOP” |
|
|
|
|
|
|
|
|
|
|
| Excessive | 1. | Damaged, out of balance or bent mower blades. | 1. | Service mower blade(s). |
| Vibration |
|
|
|
|
| 2. | Loose blade components. | 2. | Service and tighten loose parts. | |
|
|
|
|
|
|
|
| 3. | Loose or missing air lift (if equipped). | 3. | Replace air lifts. Tighten to proper torque. |
|
|
|
|
|
|
|
| 4. | Lumpy or frayed belt. | 4. | Replace belt. |
|
|
|
|
|
|
|
| 5. | Bent Idler, stationary or spindle pulley. | 5. | Replace pulley. |
|
|
|
|
|
|
30 | www.snapper.com |
