Section 4 - ADJUSTMENTS & REPAIR

WARNING

The electrolyte (acid) produces a highly explosive gas. Keep all sparks, flame and fire away from area when charging battery or when handling electrolyte or battery. Electrolyte (acid) is a highly corrosive liquid. Wear eye protection. Wash affected areas immediately after having eye or skin contact with electrolyte (acid). Battery acid is corrosive. Rinse empty acid containers with water and mutilate before discarding. If acid is spilled on battery, bench, or clothing, etc., Flush with clear water and neutralize with baking soda.

4.6.3. BATTERY SERVICE

1.Remove battery. See Section on Battery Removal.

2.Place battery in a well ventilated area on a level surface.

3.Using distilled water, refill cells as required to cover cell plates of which can also be visualized through the plastic battery case.

4.With cell caps removed, connect battery charger to battery terminals. Red to positive (+) terminal and black to negative (-) terminal.

5.Slow charge battery at 1 amp for 10 hours.

6.If battery will not accept charge or is partially charged after 10 hours of charging at 1 amp, replace with new battery.

4.6.4. BATTERY STORAGE

If mower is to be stored out of season on its rear bumper, it is recommended the battery be removed, charged and stored.

1.Remove battery. Refer to Section “BATTERY REMOVAL”.

2.Perform battery service.

3.Bring battery to full charge, if required.

4.Store battery in an area away from the RIDER on a wood surface. DO NOT STORE BATTERY ON A CONCRETE SURFACE.

4.6.5.NEW BATTERY PREPARATION 1. Remove battery from carton.

2. Place battery in a well ventilated area on a level non-concrete surface.

3. Remove battery cell caps. Fill cells as required with electrolyte (purchased separately) to proper level. Fill to 3/16” above cell plates. Filling battery with electrolyte will bring the battery to 80% charged state.

4. With cell caps removed, connect battery charger to battery terminals; RED to positive (+) and BLACK to negative (-) terminal.

IMPORTANT: 3/16” above cell plates is the recommended level. DO NOT place anything in battery other than specified electrolyte.

WARNING

DO NOT attempt to charge battery while installed on the Riding Mower. DO NOT use “BOOST” chargers on the battery. DO NOT OVERFILL!

5.Slow charge the battery at 1 amp for 2 hours to bring the battery to full charge.

6.After charging, check level of electrolyte and add as needed to bring level to 3/16” above cell plates.

7.Reinstall cell caps.

8.Slide battery partially into battery housing.

9.Connect positive (+) cable (red) first, from wiring harness to the positive terminal (+) on battery using bolt and nut provided in hardware bag. Connect negative (-) cable (black) last, to negative terminal (-) on battery using bolt and nut. Apply a small amount of grease over terminals to prevent corrosion.

10.Insert battery completely into battery housing.

11.Reinstall battery cover. See Figure 4.17.

WARNING

Shield the positive terminal with terminal cover located on battery harness. This prevents metal from touching the positive terminal which could cause sparks.

4.6.6.BATTERY TESTING

There are two types of battery tests: Unloaded and Loaded. The unloaded test is the procedure that will be discussed. It’s the simplest and most commonly used. An unloaded test is made on a battery without discharging current. To perform unloaded testing, check charge condition using either a hydrometer or voltmeter.

1.Using a voltmeter, voltage readings appear instantly to show the state of charge. Remember to hook the positive lead to the battery’s positive terminal, and the negative lead to the negative terminal.

2.A hydrometer measures the specific gravity of each cell. The specific gravity tells the degree of charge; generally, a specific gravity of about 1.265 to 1.280 indicates full charge. A reading of 1.230 to 1.260 indicates the battery should be charged. The chart on the next page shows the charge level as measured by syringe float hydrometer, digital voltmeter and five ball hydrometer.

(Battery Testing Chart on Next Page)

28

Page 28
Image 28
Snapper E331522KVE, E281022BE, E281222BE Battery Service, Battery Storage, Battery Testing Chart on Next

E281022BE, E281222BE, E331522KVE, E331522KVE, E281022BE, E281222BE, E281222BE, E281022BE, E331522KVE specifications

The Snapper E281222BE, E281022BE, and E331522KVE models are part of Snapper’s extensive range of outdoor power equipment, known for their reliability and innovative features. These models are designed to cater to the needs of homeowners and professional landscapers alike, providing efficient and effective solutions for lawn care.

Starting with the Snapper E281222BE, this model stands out with its 21-inch cutting deck, which facilitates a wider cutting path, reducing mowing time. It is equipped with a powerful Briggs & Stratton engine that delivers strong performance, allowing for efficient cutting through various types of grass and terrain. The E281222BE also features a 3-in-1 mowing system, enabling users to mulch, bag, or side discharge grass clippings, offering versatility depending on the user's preference and yard conditions.

Next in line, the Snapper E281022BE presents a similar design but with slight modifications geared towards providing an economical and efficient solution for smaller lawns. This model also has a 21-inch cutting deck and shares the robust engine characteristics of its counterpart. However, it’s particularly known for its lightweight construction, making it easier to maneuver around tight spaces and flower beds. The E281022BE promotes excellent grass management with its easy-to-use height adjustment system that allows for customized cutting heights.

The E331522KVE model, on the other hand, offers additional features aimed at enhancing user experience. It boasts a larger 33-inch cutting deck, making it ideal for medium to large lawns. This model is powered by a powerful engine designed for high performance, while its variable-speed drive system allows for greater control over mowing speed. Furthermore, the E331522KVE integrates advanced technologies such as Smart-Cut™ technology, which adjusts power and speed automatically according to grass conditions, ensuring efficient grass management in varying scenarios.

All models feature durable construction with weather-resistant components, making them reliable choices for all seasons. Ergonomically designed handles and easy-to-access controls ensure comfort during extended use. Snapper’s commitment to sustainability is reflected in these models, as they are designed to maintain optimal fuel efficiency while minimizing emissions.

In conclusion, Snapper's E281222BE, E281022BE, and E331522KVE models offer a blend of power, efficiency, and ease of use. These characteristics make them suitable for various lawn care tasks while catering to the specific needs of the user. Whether you’re maintaining a small residential lawn or managing larger grassy areas, these Snapper models provide the performance and features necessary to achieve a beautifully manicured landscape.