SECTION 3 - OPERATING INSTRUCTIONS
The operator must be familiar with the contents of this manual before attempting to attach or operate this mower. There may be specific operating and safety instructions with the tractor that are not covered in this manual. Read and follow the Instructions and Warnings in the tractor manual before operating mower.
2.1MOWER PREPARATION
Read and follow mower set up instructions and inspect mower to insure mower has been properly set up.
2.1.1.Check guards, shields, covers and deflectors to make sure all are in place, securely tightened and functioning properly.
2.1.2.Check lubrication points and gear box fluid level for proper lubrication.
2.1.3.Inspect driveline. Driveline must be securely attached to the mower gear box. All driveline shields must be in place and rotate freely.
2.1.4.Inspect mower blades for damage and wear. Replace damaged or worn blades before operating.
2.1.5.Verify that the discharge deflector is attached and in the down/closed operating position.
2.2TRACTOR PREPARATION
The following are general guidelines.
Refer to the tractor manual or the tractor manufacturer for specific instructions about the preparation and operation of the tractor.
WARNING
The tractor may require counter weights and the addition of an Operator Protective Structure when this mower is attached. Follow the Safety Instructions provided by the tractor manufacturer.
2.2.1.Remove tractor drawbar, if necessary, to prevent interference and damage to the driveline.
2.3ATTACHING MOWER TO TRACTOR
This mower is designed to attach to a tractor equipped with a standard Category 1 three (3) point hitch and 540 rpm Power Take Off (PTO).
2.3.1.Place tractor and mower on level surface. Lower tractor 3 point hitch.
2.3.2.STOP tractor. STOP engine. Set parking brake. REMOVE key.
WARNING
DO NOT get between the tractor and mower when the engine is running. STOP tractor. STOP engine. Set Brake. REMOVE key. Allow all moving parts to stop before leaving the operators position.
2.3.3.Attach lower tractor hitch arms to the pins on the mower pivoting hitch. Secure with Lynch pins.
2.3.4.Attach the top hitch link to the top hitch link on the mower. Adjust the length of the link and insert the pin. Secure pin with Lynch pin. Tighten locking device on top hitch link.
2.3.5.Adjust stabilizer bars on lower hitch arms. Refer to tractor manual for proper adjustment procedure.
2.3.6.Attach driveline to tractor Power Take Off (PTO). Twist coupling ring and slide driveline onto tractor PTO shaft. Tug aggressively on driveline yoke and insure that it is securely locked into position.
WARNING
Tractor Power Take Off (PTO) shield must be in place before operating mower. Driveline must be securely locked to tractor and mower to prevent dangerous disconnect condition.
2.3.7.Verify the minimum and maximum working lengths of the driveline. The telescoping tubes must overlap at least 1/3 of the length while in use. The driveline must not bottom out or disengage during transport. Verify driveline length before engaging Power Take Off (PTO).
WARNING
DO NOT attempt any adjustments, maintenance or service to mower with engine running. STOP tractor. STOP engine. Set Brake. REMOVE key. Allow all moving parts to stop before approaching mower.
2.4SETTING THE CUTTING HEIGHT.
2.4.1.Use tractor hitch to lift mower until all four casters are off the ground.
2.4.2.STOP engine. Remove key. Make sure all moving parts have stopped. Support mower securely to prevent it from falling.
2.4.3.Adjust cutting height by moving the spacers located on the mower casters. Placing more spacers on the bottom will increase the cutting height. Removing spacers from the bottom will lower the cutting height. Each caster has a total of 6 (1/2”) slotted spacers to adjust the height of the deck. There must always be 6 spacers installed.
A. To remove spacers, first remove the Lynch pin and washer from the top of the caster.
B. Raise cutting height by sliding spacer(s) off of top and installing on bottom. Align slotted end of spacer with the two flats on the caster shaft. Slide spacer across flats. Repeat as needed to raise height.
8
