Section 4 - ADJUSTMENT & REPAIR

WARNING

DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool.

4.2.8.38" DECK LEVEL ADJUSTMENT (SIDE TO SIDE)

NOTE: Before adjusting deck, bring tire pressure to proper P.S.I.; front 12 P.S.I., rear 12 P.S.I..

1.Move tractor to a firm, level surface.

2.Turn engine “OFF”. Remove key.

3.Place a 2-1/2” tall block under the front of the deck centered between the front lift arms. See Figure 4.13.

FRONT OF TRACTOR

2-1/2” TALL BLOCK

SIDE TO SIDE LEVEL CHECK POINTS

1-3/4” TALL BLOCK

FIGURE 4.13

4.Place a 1-3/4" tall block under the rear of the deck in the center. See Figure 4.13.

5.Position blades as shown and lower deck onto blocks. See Figure 4.13.

6.Disconnect the front lift rod and the rear hanger plates. See Figure 4.14.

7.Put the lift lever in the 3rd position from low cut.

8.Measure the distance from each blade tip to the floor. The measurements should be within 1/8" of each other. (Factory setting)

38” DECK

JAM NUT

WASHER

FRONT LIFT

ROD

HAIR PIN

FIGURE 4.14

9.If the difference is less than 1/8", go to next section, Front to rear level. If the difference is more than 1/8", adjust as described in the following steps.

10.Loosen the front adjuster nut until adjuster moves freely. Then tighten the nut until the adjuster moves only when moderate force is applied to one side of the deck. See Figure 4.15.

FRONT OF TRACTOR

ADJUSTER NUT

FIGURE 4.15

11.Adjust the side to side level of the blade tips by moving one side of the deck up or down as needed to obtain 1/8" or less side to side deck level.

12.After leveling deck, retighten the adjuster nut using

30to 40 ft. lbs.

13.Attach the rear hanger plates to the hole that most closely aligns with the pin on the deck lift bracket. Secure with washer and hair pin.

14.Adjust the swivel on the front lift rod until it lines up with the hole in the front lift bracket. (Make sure the lift rod is at the top of the slot in the deck bracket) Secure with hair pin.

21

Page 20 Page 22
Page 21
Image 21
Snapper LT150H38GKV, WLT145H38GBV important safety instructions Front of Tractor
Page 20 Page 22

WLT145H38GBV, LT150H38GKV, LT145H38GBV specifications

The Snapper LT145H38GBV, LT150H38GKV, and WLT145H38GBV are robust lawn tractors designed to provide efficient and reliable performance for homeowners and landscaping professionals alike. Each model offers a unique combination of features and technologies that enhance usability, comfort, and mowing precision.

The Snapper LT145H38GBV is powered by a 14.5 horsepower Briggs & Stratton engine, providing ample power for tackling various mowing tasks. It features a 38-inch cutting deck, made of durable steel, which allows for an optimal cutting width, making the mowing process quicker and more efficient. The LT145H38GBV also incorporates a convenient foot pedal-operated hydrostatic transmission, allowing smooth acceleration and effortless speed control without any gear shifting.

Next, the Snapper LT150H38GKV stands out with its 15 horsepower Kohler engine. This model offers increased power, making it suitable for larger lawns or tougher grass conditions. Like the LT145, it boasts a 38-inch cutting deck, but the LT150H38GKV is also equipped with a high-back seat for added comfort during longer mowing sessions. Its sturdy construction ensures durability, while its easy-to-use dashboard controls provide a user-friendly experience.

Finally, the Snapper WLT145H38GBV offers similar features to the other models but adds versatility to the mix with its wider range of capabilities. This model is designed with a tight turning radius, making it easier to navigate around flower beds and trees. The WLT145H38GBV is also powered by a reliable 14.5 horsepower engine, ensuring efficient power delivery. Its cutting deck features multiple height-adjustment settings, allowing users to customize their mowing experience according to grass types and preferences.

All three models incorporate Snapper's innovative technologies, such as the easy-access under-deck washout port that simplifies the cleaning process and supports maintenance. They also come with a variety of cutting options, providing both side discharge and mulching capabilities, enhancing lawn health and appearance. With their user-friendly designs, ample power, and strong construction, the Snapper LT145H38GBV, LT150H38GKV, and WLT145H38GBV represent an excellent choice for anyone seeking reliable lawn care solutions.
Top Page Image Contents