BLACK (NEGATIVE) CABLE

RED (POSITIVE) CABLE

TERMINAL COVER MUST SHIELD POSITIVE

TERMINAL AFTERDATE INSTALLATION

FIGURE 3

STEP 6: Take the necessary precautions, when handling fuel. Fill the fuel tank with clean fuel. Check oil and add oil if needed as stated in Engine Owners Manual. Move fuel tank selector valve handle to the desired fuel tank.

WARNING

Handle fuel with care! Use an approved fuel container. DO NOT smoke near open fuel container and keep fuel container away from open flame. DO NOT fill fuel tank indoors or when engine is running. Allow engine to cool for at least ten minutes before refilling. Wipe off any spilled fuel before starting engine. DO NOT run engine indoors. Before attempting any adjustments, maintenance, service, or repairs, stop engine and blade, always remove key from ignition switch, remove spark plug wire(s) and secure wire(s) away from spark plug(s).

STEP 7: MOWER DECK ADJUSTMENT (LEVELNESS) SIDE to SIDE and FRONT to REAR

Before making deck leveling adjustments, inflate rear tires to 12 PSI and front tires to 25 PSI. When adjusted correctly, the deck will be level side to side within 1/8”, have a low cut setting of approximately 1”, and the blades pitched approximately 3/16” higher at the rear. If adjustment is needed:

A. Place machine on a smooth level surface.

B. Check blade tips by rotating blades until tips are pointing to the sides of the deck. Check the measurement of outside blade tips to the ground on both blades. The measurement of each of the outside blade tips should be within 1/8” of each other. If measurement of the blade tips is not within 1/8”, adjustment should be made to the correct measurement.

C. Move deck lift lever and set the mower deck to the highest cutting position.

D. Relieve tension on deck lift assist spring by loosening nut on eyebolt.

E. Place 1” blocks under the front and rear edge of the mower deck.

F. Move deck lift lever and set the mower deck to a lower cutting position until deck rests on the 1” blocks. G. Loosen the nuts and bolts that secure both front deck support chains. Adjust chains until tight and retighten bolts and nuts. Torque to 70 ft. lbs.

H. Loosen the nuts that secure both rear deck support eyebolts. Adjust to remove slack from both rear chains. Tighten nuts securely.

I. Move deck lift lever and set the mower deck to the highest cutting position and recheck side to side blade tip dimensions. The difference between the two should be 1/8” or less.

NOTE: The deck timing rod (rod that runs from front deck lift arm to rear deck lift arm) is preset at the factory and requires no adjustments.

J. The leveling blocks used in Step E should result in a proper deck pitch. If a pitch adjustment is required, use the two rear deck support eyebolts. Adjust up or down as required.

K. Reinstall deck lift assist spring. Place deck in highest cutting position. Tighten nut on eyebolt until 1 1/4” of threads protrude past end of nut.

STEP 8: HYDRAULIC OIL RESERVOIRS

Check the level of the fluid in both of the fluid reservoirs. The reservoirs are located underneath the operator’s seat. Wipe away all dirt and debris from around reservoir cap before removing. Oil must remain absolutely clean! Check with machine on a level surface with engine “OFF”. Fill reservoir as needed to bring level up. The reservoir is properly filled when the fluid level is 1-1/2” below the top of the filler neck. DO NOT OVER FILL. Use clean, fresh premium automotive oil having a viscosity equivalent to SAE 20W50 API SL. The fluid should be chemically stable, incorporating rust and oxidation inhibitors. Make sure funnels, pouring spouts and oil can are completely clean. Reinstall reservoir cap.

IMPORTANT: Re-check fluid level after operating machine for several minutes and adjust level as needed. If one or both of the wheel drive systems is not pulling properly, the hydraulic system may need to be purged of entrapped air. Refer to STEP 10, “HYDRAULIC SYSTEM, PURGING”.

STEP 9: TRACKING ADJUSTMENT – TWIN STICK CONTROLS

Start machine. If the machine does not track straight when the Motion Control Levers are in the maximum forward speed position, perform the following adjustment. Rear tire pressure must be set to 12 PSI before making this adjustment.

A. Loosen bolts that secure adjustment plates and slide plates all the way forward. Retighten bolts.

B. Start machine and drive in smooth flat open area at maximum forward speed.

C.If machine tracks to the right, loosen bolts that secure the left adjustment plate. Move plate rearward to slow the left wheel. Retighten bolts.

D.If machine tracks to the left, loosen bolts that secure the right adjustment plate. Move plate rearward to slow the right wheel down. Retighten bolts. See Figure 4.

E.Drive machine again. Repeat adjustment as necessary until machine tracks straight.

2

Page 1 Page 3
Page 2
Image 2
Snapper Mount Mower manual Hydraulic OIL Reservoirs
Page 1 Page 3

Mount Mower specifications

The Snapper Mount Mower has become a standout choice for both residential and commercial lawn care professionals, known for its innovative features, powerful performance, and user-friendly design. This mower is constructed with a focus on efficiency and durability, making it a preferred option for anyone looking to maintain a well-manicured lawn.

One of the key highlights of the Snapper Mount Mower is its robust engine options. Equipped with either a reliable gas engine or a quiet yet efficient electric motor, the mower provides ample power to handle various terrain types. The commercial-grade engines ensure longevity and performance while reducing noise levels - an essential factor for suburban areas.

The mower comes with a unique floating deck design, which allows it to adapt effortlessly to uneven ground surfaces. This design feature helps the blades maintain optimal contact with the grass, resulting in a more even and clean cut. The Snapper Mount Mower is also equipped with a rear discharge system, allowing for efficient grass dispersal without the buildup of clippings, ensuring a pristine finish.

Another feature that sets this mower apart is its user-friendly control panel. The intuitive controls are strategically positioned for ease of use, allowing operators to adjust speed and blade height without losing focus on the task at hand. The adjustable cutting height ranges from 1.5 to 4 inches, giving users the flexibility to customize their mowing experience based on grass type and desired finish.

In terms of maneuverability, the Snapper Mount Mower shines with its zero-turn radius capability. This allows for quick navigation around obstacles like trees and garden beds, making mowing faster and more efficient. The sturdy tires provide excellent traction, allowing the mower to traverse various terrains with ease.

Safety features include an automatic engine shut-off when the operator leaves the seat and reinforced cutting decks designed to withstand rough conditions. The Snapper Mount Mower is also designed for easy maintenance, featuring accessible components that simplify tasks such as oil changes and blade replacements.

Innovation continues with advanced technology integration, including options for Bluetooth connectivity that allow users to monitor mower performance and maintenance schedules through a dedicated smartphone app.

In summary, the Snapper Mount Mower combines powerful performance, innovative design, and user-centered features, making it a reliable tool for achieving a beautifully maintained lawn. With its durability and efficiency, this mower not only meets but exceeds the expectations of lawn care enthusiasts and professionals alike.
Top Page Image Contents