Section 3 - OPERATING INSTRUCTIONS

3.1PRE-START CHECK LIST

Make the following checks and perform the service

required before each start-up.

3.1.1. Check tires and add or release air as needed

to bring pressure to 12 psi in drive tires. Pressure in front caster wheels should be 25 psi.

3.1.2.Check guards, deflectors and covers to make sure all are in place and securely tightened.

3.1.3.Check engine oil and add oil as needed to bring level up to the FULL mark. Refer to engine owner'smanual for oil specifications. See Figure 3.1.

3.1.8.Place mower in desired cutting height

setting. Grasp deck lift lever and depress release latch located underneath the lever. Move lever to

desired cutting height setting and release latch. Insert stop pin to desired cutting height. IMPORTANT: There is a foot assist pedal located to the right front side of the footrest. Always use this assist pedal to raise or lower the deck to the desired cutting height. See Figure 3.3.

DECK LIFT

LEVER

FIGURE 3.1

3.1.4.Check Blade Switch to insure it works freely. 1. Pull the Blade Switch up to the "ON" position to engage or turn "ON" the mower blades.

2. Push Blade Switch down to the "OFF" position to disengage (or turn "OFF") the blades.

BLADE SWITCH

FIGURE 3.2

RELEASE

LATCH

HEIGHT

FIGURE 3.3

3.1.9.Check seat belts. Mounting hardware must

be tight. Buckle must latch securely and release easily. Webbing must not display signs of

deterioration, wear or damage.

3.1.10.Check roll bar protective structure for

structural soundness (i.e. no cracks, damage, corrosion, etc.) All hardware must be tight. Roll bar must be raised and locked unless absolutely necessary (i.e. low overhead clearance). Both locking pins must be installed and securely fastened to prevent inadvertent removal. DO NOT operate a machine that has had any part of the roll bar protective structure removed, damaged, or modified in any way.

3.1.6.Clean exterior surfaces of cutting deck, engine and pumps of any accumulation of dirt, grass, oil, etc. Keep engine and pump air intake

screens and cooling fins clear at all times.

3.1.6.Add fuel to both tanks of the machine

outside where fumes can safely dissipate. Make sure both fuel filler caps are tight. Note the fuel tank selector valve. Refer to engine owner's manual for fuel specifications.

3.1.7.Adjust position of operator's seat. The seat is mounted on slides. Locate latch lever beneath the seat. Move lever towards the left and slide seat

to the desired position. Release latch. If equipped, adjust seat suspension for operator weight.

IMPORTANT: This machine is equipped with hydrostatic drive, The direction of motion and the

speed of motion are controlled by the left and right motion control levers, A small movement of these

controls can cause the machine to move instantly. DO NOT attempt to operate the machine until you read this manual and become familiar with its operation, Practice with the blades "OFF" disengaged, engine

speed at a slow setting and in an open area away from obstacles.

allow woperation.....of the machino

personnel.

10

Page 4 Page 6
Page 5
Image 5
Snapper NZM27 613KH, NZM25523KWV, NZM25613KWV, NZM19483KWV, NZM21523KWV Operating Instructions, PRE-START Check List
Page 4 Page 6

NZM21523KWV, NZM19483KWV, NZM25613KWV, NZM25523KWV, NZM27 613KH specifications

The Snapper NZM25523KWV, NZM25613KWV, NZM19483KWV, NZM21523KWV, and NZM27613KH are a series of innovative and high-performance lawn mowers designed to cater to the diverse needs of both residential and commercial users. These models showcase a range of cutting-edge features, technologies, and characteristics, making them stand out in the competitive outdoor power equipment market.

At the heart of these Snapper mowers is their powerful and efficient engine, designed to deliver robust performance while maintaining low emissions. The engines are paired with a reliable drivetrain, ensuring smooth self-propelling capabilities that significantly reduce the effort required for mowing large lawns. Users can select the desired mowing speed to suit their preferences and terrain, providing a customizable mowing experience.

One of the key features across these models is the innovative cutting system. Snapper mowers utilize a three-in-one cutting action, which allows for bagging, mulching, or side discharge of grass clippings. This versatility not only improves convenience but also empowers users to choose the best option for their specific lawn care needs. The finely engineered cutting deck design also ensures an even cut, enhancing the overall appearance of the lawn.

Durability is a hallmark of Snapper products. Each model features a heavy-duty steel construction and a robust deck that can withstand the rigors of frequent use. Users can expect these mowers to provide years of reliable service with minimal maintenance, thanks to their high-quality components and user-friendly design.

These mowers are also designed with ease of use in mind. Features such as an adjustable cutting height allow users to customize their mowing experience, ensuring optimal results for various grass types and conditions. Additionally, the ergonomic handles provide comfort during operation, reducing fatigue for the operator.

The Snapper NZM series also incorporates technological advancements such as easy-start systems for quick ignition and enhanced maneuverability. The compact design of these mowers promotes easy storage and transportability, making them an ideal choice for homeowners with limited space.

In summary, the Snapper NZM25523KWV, NZM25613KWV, NZM19483KWV, NZM21523KWV, and NZM27613KH represent a commitment to quality, efficiency, and versatility in lawn care tools. With their powerful engines, innovative cutting systems, durable construction, and user-friendly features, these mowers are well-equipped to tackle any mowing challenge, ensuring a beautifully manicured lawn every time.
Top Page Image Contents