Quick Setup Guide

Self-Propelled Mower Models SP2265 - NSP2265

Questions?

Do not return to the store. We can help.

Call Customer Service Toll-Free 1-800-317-7833Or visit our website www.snapper.com

SP2265 - NSP2265 Overview

Bail Control

1 Unpack the mower

Remove the mower from the carton. Remove all packing materials from the mower.

• Locate and identify the items included with the mower.

2

 

 

Failure to read and follow instructions in the

Read the manuals

operator's manual could result in death and/or

bodily injury.

 

 

 

Carefully read all the manuals supplied with the mower. They contain important safety, operating, and maintenance information.

3

Unfold the handle

 

 

• Turn the knobs (A, Figure 1) on either side

 

 

of the lower handle 1/4 turn to retract the

 

 

locking pins.

 

 

• Raise the lower handle, aligning it with one

 

B

 

 

of the three sets of holes in the handle

 

 

bracket (most users will prefer the middle

 

 

position).

 

 

• Turn the knobs to release the locking pins

 

A

 

 

and secure the lower handle.

 

 

5 Add oil and fuel

Move the mower outside to a flat, level surface.

Remove the oil fill cap (A, Figure 3). Add the entire contents of the supplied oil container to the engine. Replace the oil fill cap.

IMPORTANT Mower is shipped without oil in engine. Failure to add oil will result in engine damage.

Remove the fuel fill cap (B). Following the three-step instructions on the FrestStartTM card, snap the fuel preserver cartridge into the bottom of the fuel fill cap.

Add clean, fresh, UNLEADED fuel with a minimum of 87 octane, leaving one inch of space from the top of the tank for fuel expansion.

IMPORTANT Fuel tank holds less than 1/2 gallon. IMPORTANT DO NOT mix oil with fuel.

Replace the fuel fill cap, and wipe up any spills.

BA

Figure 3

DANGER

Fuel stabilizer is a hazardous chemical.

IF SWALLOWED, call a physician immediately. Fuel stabilizer contains:

2,6-di-tert-butylphenol (128-39-2) and aliphatic petroleum distillate (64742-47-8).

Running engines give off carbon monoxide, an odorless, colorless, poison gas. Breathing carbon monoxide can cause nausea, fainting, or death.

Operate this product ONLY outdoors.

Keep exhaust gas from entering a confined area through windows, doors, ventilation intakes or other openings. DO NOT operate this product inside any building or enclosure, even if windows and doors are open.

Recoil Rope

Drive

Handle

Lever

 

Fuel Fill Cap

Oil Fill and

Dipstick

Mulching

Cover

Loosen, but do not remove, the upper knobs (B) on the handle. Remove the cardboard slats.

Raise the upper handle to the operating position, and tighten the upper knobs.

Figure 1

4 Set up the recoil rope handle

Hold the bail control against the handle,

and pull the recoil rope handle out to the rope

 

guide (A, Figure 2) on the handle. Hook the recoil rope

A

into the rope guide (it might be a tight fit).

 

6 Start the mower

Move the cutting height adjust levers (A, Figure 4) to the desired cutting height.

Set the mower to mulch, discharge or bag. (See 3-in-1 instructions below.)

Hold the bail control (A, Figure 5) against the drive handle.

Pull the recoil rope handle (B) until the engine starts.

To engage the drive system, slowly pull the drive lever (C) back. To increase ground speed, slowly pull the drive lever farther back. To decrease ground speed, slowly release the drive lever.

To disengage the drive system, release the drive lever.

To stop the engine and blade, release the bail control.

A

Figure 4

A

A

B

C

Figure 5

Figure 2

Cutting Height Adjust Lever

(At Each Wheel)

Items that you will need

Unleaded Fuel (minimum 87 octane)

Utility Knife

Items Included

FreshStartTM Fuel

Preserver Cartridge

3-in-1: Convert from mulching to bagging to side-discharge:

1

For mulching:

2

To convert to bagging:

• Leave the mulching cover

• Lift the rear door (A, Figure 7).

(Figure 6) in place.

• Holding the rear door open, attach the grass catcher (B) to the rear of the mower.

• Make sure the hooks (A, Figure 8) on either side of the catcher frame hook

A

3 To convert to side-discharge:

A

Lift the mulching cover (A, Figure 9).

Install the side discharge deflector (B) onto

 

B

the mower deck. Make sure the upper tabs (A,

B

 

Figure 10) of the deflector are hooked behind

 

 

 

the mulching cover rod, and the deck tabs

 

Figure 7

 

Figure 9

 

 

stick up through the locking slots (B).

 

 

 

 

Side Discharge

Figure 6

onto the rear door rod (B).

A

• Release the mulching cover (it will lay

A

 

Deflector

• Release the rear door (it will lay on top of the grass catcher).

on top of the side discharge deflector).

Grass Catcher

SAE30W

Operator’s

Oil

Manual

B

B

Figure 8

Figure 10

© Briggs & Stratton Corporation

Form No. 7101632 (Rev. ‘-’, 3/14/2008)

We reserve the right to improve our products and make changes in specifications, designs, and standard equipment without notice and without incurring obligation.

TP 1099-5328---WB-N

Page 1
Image 1
Snapper setup guide SP2265 NSP2265 Overview, Unpack the mower, Unfold the handle, Add oil and fuel, Start the mower