Setting Up the System
English
Setting Up the System
Setup after Connection | 6 |
After components have been connected to INPUT1 or INPUT2,
Follow the procedure described below and make settings as they apply to the type of components connected.
Screen Mode setup
Note
These settings are required only when using the following input signal refresh rates: 1 31.5 kHz horizontal / 60 Hz vertical; 2
48.4 kHz horizontal / 60 Hz vertical, or 56.5 kHz horizontal / 70 Hz
vertical. No manual setup is necessary for signals with other7 refresh rates, since adjustments are performed automatically (the SETTING item will not be displayed).
1Switch MAIN POWER on the connection panel to the on position to turn on the unit’s main power. The STANDBY/ON indicator lights red.
2Press STANDBY/ON to put the unit in the operation mode.
The STANDBY/ON indicator turns green.
3Select INPUT1 or INPUT2.
4Press MENU to display the menu screen. The menu screen appears.
MAIN MENU |
|
|
|
|
| INPUT1 |
PICTURE | SCREEN | SET UP | OPTION | |||
C O N T R A S T |
| : | 0 |
|
|
|
BR I GHT . |
| : | 0 |
|
|
|
R. L E V E L |
| : + 6 0 |
|
|
| |
G. L E V E L |
| : + 6 0 |
|
|
| |
B. L E V E L |
| : + 6 0 |
|
|
| |
H. E NHAN CE | : | 0 |
|
|
| |
V . E NHAN CE | : | 0 |
|
|
| |
RE S E T |
|
|
|
|
|
|
SELECT |
| SET | ENTER | MENU | EXIT | |
|
|
|
|
|
| 8 |
Press 5/∞ to select SETTING, then press SET.
MAIN | MENU |
|
|
|
|
| INPUT1 |
PICTURE | SCREEN | SET UP | OPTION | ||||
| I NP UT L A B E L |
| : I NP UT 1 | ||||
| POWE R | MA NAGEME NT : OF F |
|
| |||
| C L AMP | P O S I T I O N | : A U T O |
|
| ||
| S E T T I N G |
| : V G A |
|
| ||
| SELECT | SET | ENTER | MENU | EXIT | ||
Press 2/3 to select the display mode.
S E T T I N G : V G A
SELECT SET SET MENU EXIT
1When the input signal has a refresh rate of 31.5 kHz (horizontal) and 60 Hz (vertical), pressing 2/3 will cause the display mode to change alternately as follows:
VGA | WIDE VGA |
2When the input signal has a refresh rate of 48.4 kHz horizontal / 60 Hz vertical, or 56.5 kHz horizontal / 70 Hz vertical, pressing 2/3 will cause the display mode to change alternately as follows:
XGA | WIDE XGA |
When the setup is completed, press MENU to exit
5Press 2/3 to select SET UP.
MAIN | MENU |
|
|
|
|
| INPUT1 |
PICTURE | SCREEN | SET UP | OPTION | ||||
| I N P UT L A B E L |
| : I N P UT 1 | ||||
| POWE R | MA NAGEME NT : OF F |
|
| |||
| C L AMP | P O S I T I O N | : A U T O |
|
| ||
| S E T T I N G |
| : V G A |
|
| ||
| SELECT | SET | ENTER | MENU | EXIT | ||
the menu screen.
Note
Make this setup for each input (INPUT1 and INPUT2).
14
En
