SECTION 4 - SERVICE & LUBRICATION INFORMATION
| HOURS | PROCEDURE | COMMENTS |
|
|
| |||
|
| Check all fasteners for proper tightness |
|
|
|
|
|
|
|
|
| Change Engine Oil and Filter at 5 hours | See engine manual |
|
|
| |||
|
| Change Hydraulic Oil and Filter at 25 hours | Use SAE |
|
|
| |||
|
|
| Reservoir capacity 1 Gal. |
|
| ||||
| 8 HOURS | Check/Change Engine Oil | Change oil if extreme dusty conditions | ||||||
| (Daily) | Clean Air Filter | More often if needed |
|
| ||||
|
| Clean Blower screen | More often if needed |
|
| ||||
|
| Remove Debris from under Belt Cover | More often if needed |
|
| ||||
|
| Sharpen Cutter Blades | Tighten Cap Screw to 70 - 80 ft. lbs. | ||||||
|
| Grease Cutter Spindle Bearings | Use Chevron SRI Grease (NLGI2). | ||||||
|
| Check Hydraulic Reservoir | Add oil if needed |
|
|
| |||
| 40 HOURS | Check Tire Pressure | Add or adjust as Required |
|
| ||||
| (Weekly) | Check Safety Interlock System | Inspect Switches for ease of Operation | ||||||
|
| Grease Traction Control Levers | General Purpose Grease |
|
| ||||
|
| Inspect Traction Lock for Wear | Replace if Worn |
|
|
| |||
|
| Change Engine Oil | More often if needed |
|
| ||||
|
| Replace Air Filter | More often if needed |
|
| ||||
|
| Grease Caster Wheel Bearings | General Purpose Grease |
|
| ||||
|
| Grease Caster Wheel Pivot | General Purpose Grease |
|
| ||||
|
| Grease Idler Arm Pivots | General Purpose Grease |
|
| ||||
| 200 HOURS | Fuel Filter | Replace with Snapper P/N | ||||||
| (Monthly) | Check all Fasteners for Proper tightness | See Torque Specifications |
|
| ||||
|
| Change Engine Oil Filter | See Engine Manual |
|
| ||||
|
| Clean and Adjust Spark Plugs | See Engine Manual |
|
| ||||
|
| Check Belt Tension | See Operator’s Manual |
|
| ||||
|
| Lube Controls and Linkages | Use Medium Duty Oil |
|
| ||||
|
| Change Hydraulic Oil and Filter | Use SAE |
|
| ||||
|
|
| Reservoir capacity 1 Gal. |
|
| ||||
|
|
|
|
|
|
|
| ||
|
|
|
|
| GREASE | GREASE | |||
|
| GREASE ZERK LOCATION |
|
| DAILY | WEEKLY | |||
| 1 on the Hydro Pump Belt Idler Arm Pivot |
|
|
|
|
| X | ||
| 1 on each Spindle Housing (Total of 2 on 36” Deck & 3 on 48”, 52”, 48”, & 61” Decks) |
|
| X |
|
| |||
| 1 on each Idler Arm Pivot (Total of 1 on 36” Deck & 2 on 48”, 52”, 48”, & 61” Decks) |
|
|
| X | ||||
| 1 on each Caster Support Arm (Total of 2) |
|
|
|
|
| X | ||
| 1 on each Caster Wheel (Total of 2) |
|
|
|
|
| X | ||
| 1 on each Traction Control Lever (Total of 2) |
|
|
|
|
| X | ||
|
| MAINTENANCE/REPLACEMENT PARTS |
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
| MAINTENANCE PARTS |
|
|
|
|
|
|
|
|
| 36” Cutter Blade (Requires Two Blades) |
|
|
|
|
|
| |
|
| 48” Cutter Blade (Requires Three Blades) |
|
|
|
|
|
| |
|
| 52” Cutter Blade (Requires Three Blades) |
|
|
|
|
|
| |
|
| 61” Cutter Blade (Requires Three Blades) |
|
|
|
|
|
| |
|
| 36” Deck Engine to Cutting Deck Belt |
|
|
|
|
|
| |
|
| 48” Deck Engine to Cutting Deck Belt |
|
|
|
|
|
| |
|
| 48” Deck Spindle to Spindle Belt |
|
|
|
|
|
| |
|
| 52” Deck Engine to Cutting Deck Belt |
|
|
|
|
|
| |
|
| 52” Deck Spindle to Spindle Belt |
|
|
|
|
|
| |
|
| 61” Deck Engine to Cutting Deck Belt |
|
|
|
|
|
| |
|
| 61” Deck Spindle to Spindle Belt |
|
|
|
|
|
| |
|
| Parts Manual for Pro Hydro Series 1 |
| 06926 |
|
|
|
|
|
20
