Snapper YZ13331be, YZ13381BE, YZ145332BE, YZ145382BE Troubleshooting, Excessive Vibration

Models: YZ13331be, YZ13381BE, YZ145332BE, YZ145382BE

1 32
Download 32 pages 29.53 Kb
Page 23
Image 23

TROUBLESHOOTING

PROBLEM

 

PROBABLE CAUSE

 

CORRECTIVE ACTION

 

 

 

Excessive Vibration

1. Damaged, out of balance or bent mower blades.

1. Service mower blade(s).

 

 

 

 

2. Loose blade components.

2. Service and tighten loose parts.

 

 

 

 

3. Loose or missing air lift (if equipped).

3. Replace air lifts. Tighten to proper torque.

 

 

 

 

4. Lumpy or frayed belt

4. Replace belt.

 

 

 

 

5. Bent Idler, stationary or spindle pulley

5. Replace pulley.

 

 

 

Rider Will Not Move Or

1. Joystick in the neutral “N” position.

1. Place joystick in desired speed position.

Loss Of Traction

2. Roll release lever is in “ROLL” position.

2. Move roll release lever to the engaged position.

 

3.

Low transmission hydraulic oil level.

3.

Contact authorized SNAPPER dealer.

 

 

 

 

 

 

4.

Parking Brake engaged.

4.

Move parking brake to disengaged position..

 

 

 

 

 

 

5.

Traction drive belt requires replacement

5.

Replace traction drive belt.

 

 

 

Blade(s) Not Cutting

1. Blade engagement switch in the “OFF” position.

1. Move blade switch to the “ON” position.

 

 

 

 

 

 

2.

Clutch belt slipping.

2.

Replace clutch belt.

 

 

 

 

 

 

3.

Mower belt slipping.

3.

Replace mower belt.

 

 

 

 

 

 

4.

Electric clutch not functioning.

4.

Contact authorized SNAPPER dealer.

 

 

 

 

Cutting Grass

1. Uneven tire pressure.

1.

Bring to proper pressure.

 

 

 

 

Improperly

2. Cutting height too low or high.

2.

Adjust cutting height.

 

 

 

 

 

 

3.

Engine speed too slow.

3.

Move throttle control to “FAST” position.

 

 

 

 

 

 

4.

Forward speed too fast.

4.

Move joystick to a slower speed.

 

 

 

 

 

 

5.

Terraced cut, side to side.

5.

Adjust side to side level

 

 

 

 

 

 

6.

Excessive deck pitch, front to rear.

6.

Adjust front to rear pitch.

 

 

 

 

 

 

7.

Cutting blade(s) dull or damaged.

7.

Sharpen cutting edges or replace blade(s).

 

 

 

 

 

 

8.

Blade belt slipping.

8.

Replace blade belt.

 

 

 

 

 

9.

Check electric clutch.

9. Adjust to proper specifications. (33” Deck Only)

 

 

 

 

10. Check clutch belt.

10. Replace clutch belt.

 

 

 

 

Poor Grass Discharge

1. Engine speed too slow.

1.

Move throttle control to “FAST” position.

 

2.

Forward speed too fast.

2.

Move joystick to a slower speed.

 

 

 

 

 

 

3.

Grass is wet.

3.

Mow when grass is dry.

 

 

 

 

 

 

4.

Excessively worn or damaged blade(s).

4.

Service mower blade(s)

 

 

 

 

 

 

5.

Build up of grass clippings and debris under deck.

5.

Clean deck.

 

 

 

 

 

 

6.

Improper blade(s) installed on deck.

6.

Install proper SNAPPER blades.

 

 

 

 

 

 

7.

Blade(s) installed improperly on deck.

7.

Install blades properly.

 

 

 

 

Battery Will Not Charge

1. Poor cable connections.

1.

Clean cables and battery terminals.

 

2.

Bad battery cell(s)

2.

Replace with new battery.

 

 

 

 

 

 

3.

Faulty alternator.

3.

Contact engine manufacturer’s dealer.

 

 

 

 

Oil Leaking

1. Leaking hose fittings, clamps or reservoir.

1.

Verify fittings and hose clamps are tight.

 

 

 

 

 

23

Page 23
Image 23
Snapper YZ13331be, YZ13381BE, YZ145332BE, YZ145382BE Troubleshooting, Excessive Vibration, Rider Will Not Move Or