Manuals / Snapper / Lawn and Garden / Lawn Mower

Snapper ZM5201M, ZM5201M, ZM6101M, ZM6101M, ZM2501KH, ZM5201M Primary Maintenance

Models: ZM5201M, ZM5201M, ZM6101M ZM6101M, ZM2501KH, ZM5201M

1 35

Download 35 pages 6.61 Kb

Page 29

Manual background

PRIMARY MAINTENANCE

29

Image 29

Snapper ZM5201M, ZM5201M, ZM6101M, ZM6101M, ZM2501KH, ZM5201M important safety instructions Primary Maintenance

Contents

POWER UNIT MODELS Safety Instructions & Operator’s Manual forMID MOUNT Z-RIDER ZERO TURNING HYDRO DRIVE SERIES MOWER UNIT MODELSIMPORTANT SAFETY INSTRUCTIONS 1. DO NOT store machine or fuel container inside where fumes may reach an open flame, spark or pilot light such as in a water heater, furnace, clothes dryer or other gas appliance. Allow engine to cool before storing machine in an enclosure. Store fuel container out of the reach of children in a well ventilated, unoccupied building. Shut off fuel when equipped with valve while storing or transporting machine IMPORTANT SAFETY INSTRUCTIONSMAINTENANCE IMPORTANT SAFETY INSTRUCTIONSTABLE OF CONTENTS 1.2 NOMENCLATURE Section 1 - FAMILIARIZATION1.1 INTRODUCTION CHOKE “ON” ENGINE CONTROLS CHOKE Section 2 - SAFETY MESSAGES AND SYMBOLSRABBIT “FAST” ENGINE SPEED CHOKE “OFF”“START” “RUN” KEY SWITCH “STOP” MOTION CONTROL MULTI-DIRECTIONAL Section 2 - SAFETY MESSAGES AND SYMBOLSBLADES ENGAGED “ON” BLADE SWITCH “ON” LIGHT SWITCH HOUR METER “OFF” BLADES DISENGAGED “OFF”2.1 PRE-START CHECK LIST Section 3 - OPERATING INSTRUCTIONS2.2 STARTING & STOPPING - ENGINE, BLADES, PARKING BRAKE Section 3 - OPERATING INSTRUCTIONS2.2.1. STARTING ENGINE FAST POSITION CHOKE POSITION2.2.5. PARKING BRAKE Section 3 - OPERATING INSTRUCTIONSJOYSTICK IN NEUTRAL POSITION PARKING BRAKE LEVER IN ENGAGED “ON” POSITIONSection 3 - OPERATING INSTRUCTIONS NOTE The engine does not have to be running to adjust cutting height3.2 SERVICE - AFTER FIRST 5 HOURS Section 4 - MAINTENANCE3.1 INTRODUCTION 3.2.2. CHECK MOWER BLADEa. Lower deck to lowest setting b. Remove foot rest. See Figure Section 4 - MAINTENANCE3. Power Transfer Shaft Section 4 - MAINTENANCE3.3.3. RIDING MOWER - LUBRICATION 1. Front Wheel Bearings 2. Transaxle3.6 DECK REMOVAL Section 4 - MAINTENANCEREAR LIFT ARM REAR LINK SHOULDERPLATE BOLT WASHER NUT THREADED END Section 4 - MAINTENANCEFRONT AXLE COTTER PIN WASHERS PULL BAR CLEVIS PIN TRANSFER SHAFT LOCK COLLAR TAKE OFF SHAFTDANGER Section 5 - ADJUSTMENTS & REPAIR4.2.1. MOWER DECK ADJUSTMENT LEVELNESS Continued Section 5 - ADJUSTMENTS & REPAIRFRONT to REAR LEVEL FIGURE 4.2A4.3 PARKING BRAKE ADJUSTMENT Section 5 - ADJUSTMENTS & REPAIR4.6 MOWER DRIVE BELT REPLACEMENT Section 5 - ADJUSTMENTS & REPAIR4.6.2. BELT REPLACEMENT 4.5.2. BLADE SHARPENING4.7 BATTERY 4.7.1. BATTERY REMOVAL Section 5 - ADJUSTMENTS & REPAIRBattery Condition Chart Section 5 - ADJUSTMENTS & REPAIREngine Loses Power TROUBLESHOOTINGStarter Will Not Crank EngineBattery Will Not Charge TROUBLESHOOTINGTractor Will Not Move Loss Of TractionMAINTENANCE PARTS SERVICE SCHEDULEMAINTENANCE/REPLACEMENT PARTS 52” MOWER DECK2 YEAR LIMITED WARRANTY PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE Page Page Page MANUAL No. 7-3703 I.R. 5/15/00 Safety Instructions & Operator’s Manual forMID MOUNT Z-RIDER ZERO TURNING HYDRO DRIVE SERIES