Manuals / Snapper / Lawn and Garden / Lawn Mower

Snapper ZM6101M, ZM2501KH, ZM5201M Safety Messages And Symbols, Blades Disengaged “Off”

Models: ZM5201M, ZM5201M, ZM6101M ZM6101M, ZM2501KH, ZM5201M

1 35

Download 35 pages 6.61 Kb

Page 8

Image 8

Section 2 – SAFETY MESSAGES AND SYMBOLS

“START”

“RUN”

KEY SWITCH

“STOP”

MOTION CONTROL

MULTI-DIRECTIONAL

BLADES ENGAGED “ON”

BLADE SWITCH

“ON”

LIGHT SWITCH

HOUR METER

“OFF”

BLADES DISENGAGED “OFF”

DANGER! ROTATING BLADES

KEEP CHILDREN AND OTHERS OUT OF MOWING AREA

DANGER! ROTATING BLADES

Page 8

Image 8

Snapper ZM6101M, ZM2501KH, ZM5201M Safety Messages And Symbols, Blades Disengaged “Off”, Danger! Rotating Blades

Contents

Safety Instructions & Operator’s Manual for POWER UNIT MODELSMID MOUNT Z-RIDER ZERO TURNING HYDRO DRIVE SERIES MOWER UNIT MODELSIMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS 1. DO NOT store machine or fuel container inside where fumes may reach an open flame, spark or pilot light such as in a water heater, furnace, clothes dryer or other gas appliance. Allow engine to cool before storing machine in an enclosure. Store fuel container out of the reach of children in a well ventilated, unoccupied building. Shut off fuel when equipped with valve while storing or transporting machineIMPORTANT SAFETY INSTRUCTIONS MAINTENANCETABLE OF CONTENTS 1.2 NOMENCLATURE Section 1 - FAMILIARIZATION1.1 INTRODUCTION Section 2 - SAFETY MESSAGES AND SYMBOLS CHOKE “ON” ENGINE CONTROLS CHOKERABBIT “FAST” ENGINE SPEED CHOKE “OFF”Section 2 - SAFETY MESSAGES AND SYMBOLS “START” “RUN” KEY SWITCH “STOP” MOTION CONTROL MULTI-DIRECTIONALBLADES ENGAGED “ON” BLADE SWITCH “ON” LIGHT SWITCH HOUR METER “OFF” BLADES DISENGAGED “OFF”Section 3 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LISTSection 3 - OPERATING INSTRUCTIONS 2.2 STARTING & STOPPING - ENGINE, BLADES, PARKING BRAKE2.2.1. STARTING ENGINE FAST POSITION CHOKE POSITIONSection 3 - OPERATING INSTRUCTIONS 2.2.5. PARKING BRAKEJOYSTICK IN NEUTRAL POSITION PARKING BRAKE LEVER IN ENGAGED “ON” POSITIONNOTE The engine does not have to be running to adjust cutting height Section 3 - OPERATING INSTRUCTIONSSection 4 - MAINTENANCE 3.2 SERVICE - AFTER FIRST 5 HOURS3.1 INTRODUCTION 3.2.2. CHECK MOWER BLADESection 4 - MAINTENANCE a. Lower deck to lowest setting b. Remove foot rest. See FigureSection 4 - MAINTENANCE 3. Power Transfer Shaft3.3.3. RIDING MOWER - LUBRICATION 1. Front Wheel Bearings 2. TransaxleSection 4 - MAINTENANCE 3.6 DECK REMOVALSection 4 - MAINTENANCE REAR LIFT ARM REAR LINK SHOULDERPLATE BOLT WASHER NUT THREADED ENDFRONT AXLE COTTER PIN WASHERS PULL BAR CLEVIS PIN TRANSFER SHAFT LOCK COLLAR TAKE OFF SHAFTSection 5 - ADJUSTMENTS & REPAIR DANGERSection 5 - ADJUSTMENTS & REPAIR 4.2.1. MOWER DECK ADJUSTMENT LEVELNESS ContinuedFRONT to REAR LEVEL FIGURE 4.2ASection 5 - ADJUSTMENTS & REPAIR 4.3 PARKING BRAKE ADJUSTMENTSection 5 - ADJUSTMENTS & REPAIR 4.6 MOWER DRIVE BELT REPLACEMENT4.6.2. BELT REPLACEMENT 4.5.2. BLADE SHARPENINGSection 5 - ADJUSTMENTS & REPAIR 4.7 BATTERY 4.7.1. BATTERY REMOVALSection 5 - ADJUSTMENTS & REPAIR Battery Condition ChartTROUBLESHOOTING Engine Loses PowerStarter Will Not Crank EngineTROUBLESHOOTING Battery Will Not ChargeTractor Will Not Move Loss Of TractionSERVICE SCHEDULE MAINTENANCE PARTSMAINTENANCE/REPLACEMENT PARTS 52” MOWER DECK2 YEAR LIMITED WARRANTY PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE Page Page Page MANUAL No. 7-3703 I.R. 5/15/00 Safety Instructions & Operator’s Manual forMID MOUNT Z-RIDER ZERO TURNING HYDRO DRIVE SERIES