Manuals
/
Snapper
/
Lawn and Garden
/
Lawn Mower
Snapper
ZM6101M, ZM2501KH, ZM5201M, ZM5201M, ZM5201M, ZM6101M Primary Maintenance
Models:
ZM5201M, ZM5201M, ZM6101M
ZM6101M, ZM2501KH, ZM5201M
1
30
35
35
Download
35 pages
6.61 Kb
27
28
29
30
31
32
33
34
<
>
Troubleshooting
Battery Condition Chart
Mower Drive Belt Replacement
Warranty
Maintenance
NOTE The engine does not have to be running to adjust cutting height
BATTERY 4.7.1. BATTERY REMOVAL
a. Lower deck to lowest setting b. Remove foot rest. See Figure
Safety Messages And Symbols
How to
Page 30
Image 30
PRIMARY MAINTENANCE
30
Page 29
Page 31
Page 30
Image 30
Page 29
Page 31
Contents
MID MOUNT Z-RIDER ZERO TURNING HYDRO DRIVE SERIES
Safety Instructions & Operator’s Manual for
POWER UNIT MODELS
MOWER UNIT MODELS
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
1. DO NOT store machine or fuel container inside where fumes may reach an open flame, spark or pilot light such as in a water heater, furnace, clothes dryer or other gas appliance. Allow engine to cool before storing machine in an enclosure. Store fuel container out of the reach of children in a well ventilated, unoccupied building. Shut off fuel when equipped with valve while storing or transporting machine
IMPORTANT SAFETY INSTRUCTIONS
MAINTENANCE
TABLE OF CONTENTS
Section 1 - FAMILIARIZATION
1.1 INTRODUCTION
1.2 NOMENCLATURE
RABBIT “FAST” ENGINE SPEED
Section 2 - SAFETY MESSAGES AND SYMBOLS
CHOKE “ON” ENGINE CONTROLS CHOKE
CHOKE “OFF”
BLADES ENGAGED “ON” BLADE SWITCH “ON” LIGHT SWITCH HOUR METER “OFF”
Section 2 - SAFETY MESSAGES AND SYMBOLS
“START” “RUN” KEY SWITCH “STOP” MOTION CONTROL MULTI-DIRECTIONAL
BLADES DISENGAGED “OFF”
Section 3 - OPERATING INSTRUCTIONS
2.1 PRE-START CHECK LIST
2.2.1. STARTING ENGINE
Section 3 - OPERATING INSTRUCTIONS
2.2 STARTING & STOPPING - ENGINE, BLADES, PARKING BRAKE
FAST POSITION CHOKE POSITION
JOYSTICK IN NEUTRAL POSITION PARKING BRAKE LEVER IN ENGAGED “ON”
Section 3 - OPERATING INSTRUCTIONS
2.2.5. PARKING BRAKE
POSITION
NOTE The engine does not have to be running to adjust cutting height
Section 3 - OPERATING INSTRUCTIONS
3.1 INTRODUCTION
Section 4 - MAINTENANCE
3.2 SERVICE - AFTER FIRST 5 HOURS
3.2.2. CHECK MOWER BLADE
Section 4 - MAINTENANCE
a. Lower deck to lowest setting b. Remove foot rest. See Figure
3.3.3. RIDING MOWER - LUBRICATION 1. Front Wheel Bearings
Section 4 - MAINTENANCE
3. Power Transfer Shaft
2. Transaxle
Section 4 - MAINTENANCE
3.6 DECK REMOVAL
FRONT AXLE COTTER PIN WASHERS PULL BAR CLEVIS PIN
Section 4 - MAINTENANCE
REAR LIFT ARM REAR LINK SHOULDERPLATE BOLT WASHER NUT THREADED END
TRANSFER SHAFT LOCK COLLAR TAKE OFF SHAFT
Section 5 - ADJUSTMENTS & REPAIR
DANGER
FRONT to REAR LEVEL
Section 5 - ADJUSTMENTS & REPAIR
4.2.1. MOWER DECK ADJUSTMENT LEVELNESS Continued
FIGURE 4.2A
Section 5 - ADJUSTMENTS & REPAIR
4.3 PARKING BRAKE ADJUSTMENT
4.6.2. BELT REPLACEMENT
Section 5 - ADJUSTMENTS & REPAIR
4.6 MOWER DRIVE BELT REPLACEMENT
4.5.2. BLADE SHARPENING
Section 5 - ADJUSTMENTS & REPAIR
4.7 BATTERY 4.7.1. BATTERY REMOVAL
Section 5 - ADJUSTMENTS & REPAIR
Battery Condition Chart
Starter Will Not Crank
TROUBLESHOOTING
Engine Loses Power
Engine
Tractor Will Not Move
TROUBLESHOOTING
Battery Will Not Charge
Loss Of Traction
MAINTENANCE/REPLACEMENT PARTS
SERVICE SCHEDULE
MAINTENANCE PARTS
52” MOWER DECK
2 YEAR LIMITED WARRANTY
PRIMARY MAINTENANCE
PRIMARY MAINTENANCE
PRIMARY MAINTENANCE
PRIMARY MAINTENANCE
Page
Page
Page
Safety Instructions & Operator’s Manual for
MID MOUNT Z-RIDER ZERO TURNING HYDRO DRIVE SERIES
MANUAL No. 7-3703 I.R. 5/15/00
