Sonance CB1 installation instructions Specifications, Installation

33-1892 CB1-inst8-02.qxd 9/23/02 2:27 PM Page 1

INSTALLATION INSTRUCTIONS

CB1

ONE ZONE CONNECTING BLOCK

The Model CB1 provides a quick low cost means of connecting all Sonance IR Receivers and Keypads to four single or four dual emitters and a power supply in an infrared repeater system. It can also provide a low cost means of emitter expansion in existing systems, or to connect multiple emitters at the output of other Sonance devices, such as the ACB1 Amplified Connecting Blocks.

EMITTERS

CB1

ONE ZONE

CONNECTING BLOCK

PWR	+12VDC	GND	GND	SIGNAL	RCVR
					IR

Fig. 1 CB1 One Zone Connecting Block Mounted in 3” SNAPTRACK™

(SNAPTRACK is a registered trademark of AUGAT)

SPECIFICATIONS

•Inputs: 1-Screw type 4-terminal plug-in. 1-IR Receiver “IR RCVR” 3.5 mm stereo mini jack.

•Outputs: 4-Emitter ports (3.5mm mono mini jacks) parallel driven.

•Contains a 470 Ohm resistor in series with each emitter output.

•Sonance E1, VE1, E2 & VE2 Mini Emitters may be used.

•Power requirements: 12 volts DC. Uses PS1 or PS2 Power Supplies. NOTE: A power supply is not connected to the CB1 when it is used as an emitter expander.

•2.1 mm coaxial power jack.

•Dimensions: 2-3/8" W x 3" D x 13/16" H.

INSTALLATION

Fig. 2, next page, illustrates a typical installation using the CB1 in an IR repeater system. A variety of Sonance IR Receivers are shown. When configuring a system, please keep the following items in mind:

1.More IR Receivers may be wired in parallel, in the same manner as shown, up to a maximum of twelve. More than twelve is not recommended because IR noise picked up by the many IR receivers may cause erratic operation and reduce remote control range.

2.Be sure to connect the +12V, Output, and GND of each IR Receiver and keypad to the respective +12VDC, SIGNAL, and GND of the connecting block as shown.

3.Please Note:

a)Each IR receiver draws 10 milliamps.

b)The maximum current for proper operation from the PS1 Power Supply is 200 milliamps.

c)The maximum current for proper operation from the PS2 Power Supply is 1000 milliamps.

d)When using combinations of keypads and receivers, do not exceed the maximum current of the power supplies as noted above.

For example, 6 receivers and 8 emitters could be used with one PS1 Power Supply. If the current capability of the PS1 will be exceeded, use the PS2 Power Supply instead.

CAUTION: Do not use unregulated 12V power supply adapters from other manufacturers. These may deliver excessive voltage to the IR receivers and cause them to “latch-up”. When this occurs, the “talk-back” LEDs and VE1 Visible emitters (if used) will stay on continuously!

4.For clarity, connections in this illustration are shown going to a 3-conductor bus in a "daisy chain"

fashion. In an actual installation, however, it is recommended that 3-conductor "home-runs" be pulled from each room to the CB1 Connecting Block in the main room. This maintains higher power supply voltage to each IR receiver and keypad for best operation.

5.The "IR RCVR" jack on the CB1 allows the SMR1P and the CR1 (with a 3.5 mm stereo mini plug) to be plugged directly into the CB1. You can do this when the CB1 Connecting Block is within reach of the 7-foot cable; such as when installing the SMR1P in a cabinet where the controlled equipment is behind closed doors.

CAUTION: Plug only Sonance IR Receivers equipped with a stereo mini plug into the IR RCVR jack. Do not plug in emitters or other devices; to do so will destroy emitters and damage power supplies!

6.The emitter ports are driven in parallel with a 470 Ohm resistor connected in series with each port. The resistors ensure proper current sharing to each emitter. When using less than 4 emitters, you may plug them into any of the 4 emitter ports without regard to order.

Pg1