09/12/31 CD-DH899N (SEC-LAG) EN.fmE-11In this example, the clock is set for the 12-hour (AM 12:00)
display.
To confirm the time display:
Press the CLOCK/TIMER button. The time display will
appear for about 5 seconds.
Note:
The “CLOCK” will appear or time will be displayed when
the AC power supply is restored after a power failure or
unplugging the unit. If incorrect, readjust the clock as
follows.
To readjust the clock:
Perform “Setting the clock” from step 1. If the “CLOCK”
does not appear in step 2, step 3 (for selecting the 12-hour
or 24-hour display) will be skipped.
To change the 12-hour or 24-hour display:
Once timer:
Once timer play works for one time only at a preset time.
Daily timer:
Daily timer play works at the same preset time every day.
For example, set the timer as a wake-up call every
morning.
Using the once timer and daily timer in combination:
For example, use the once timer to listen a radio program,
and use the daily timer to wake up.
1Press the ON/STAND-BY button to turn the power on.
2Press the CLOCK/TIMER button.
3Within 10 seconds, press the MEMORY button.
Press the or button to select 12-hour or
24-hour display and then press the MEMORY button.
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
The 12-hour display will appear.
(AM 0:00 - PM 11:59)
The 24-hour display will appear.
(0:00 - 23:59)
4To adjust the hour, pre ss the or button and
then press the MEMORY button. Press the or
button once to advance the time by 1 hour. Hold it
down to advance continuously.
5To adjust the minutes, press the or button
and then press the MEMORY button. Press the
or button once to advance the time by 1 minute.
1Clear all the programmed contents. [Refer to “Factory
reset, clearing all memory” on page 14 for details.]
2Perform “Setting the clock” from step 1 onwards.
Setting the clock (Remote control only)CD
USB
TAPE
“AM 12:00”
“AM 0:00”
“0:00”
Before setting timer:
●Check that the clock is set to the correct time (refer to
page 11). If it is not set, you cannot use the timer
function.
●For timer playback: Plug in USB or load disc/cassette
or dock iPod to be played.
1Press the ON/STAND-BY button to turn the power on.
2Press and hold the CLOCK/TIMER button.
3Within 10 seconds, press the or button to
select “ONCE SET” or “DAILY SET”, and press the
MEMORY button. Set the clock to the correct time if
“ONCE SET” or “DAILY SET” does not appear.
4Within 10 seconds, press the or button to
select “TIMER SET”, and press the MEMORY button.
5To adjust the hour, press the or button and then
press the MEMORY button.
6To adjust the minutes, press the or button and
then press the MEMORY button.
7Set the time to finish as in steps 5 and 6 above.
8To select the timer playback source (CD, TUNER, USB,
iPod, TAPE or AUDIO IN), press the or button.
Press the MEMORY button.
When you select the tuner, select a station by pressing
the or button, and then press the MEMORY
button. If a station has not been programmed, “NO
PRESET” will be displayed and timer setting will be
canceled.
9Adjust the volume using the VOLUME control, and then
press the MEMORY button. Do not turn the volume up
too high.
10 Press the ON/STAND-BY button to enter the power
stand-by mode. The “TIMER” indicator lights up and
the unit is ready for timer playback.
Timer and sleep operation (Remote control only)Once timer
Daily timer
Start Stop
1 minute or more
Start Stop