Remove the jumper to set to OFF, and install the jumper to set to ON. The recommended jumper is AMP* Shunts
The following table shows the function of each jumper.
Jumper | Function |
|
|
|
|
| |||||
DEVICE | The setting of this jumper determines whether the | ||||||||||
TYPE | SCSI device type code in the inquiry data is WO | ||||||||||
| or |
|
|
|
|
| |||||
|
| ON: | WORM |
|
|
|
|
| |||
|
| OFF: |
|
|
|
|
| ||||
|
|
|
|
|
|
| |||||
ID SELECT | Assign the drive unit’s ID number by setting these | ||||||||||
| jumpers to ON or OFF. Do not assign the same | ||||||||||
| number as one used for other SCSI device. | ||||||||||
|
|
|
|
|
|
|
|
| |||
|
|
| ID number |
| Jumper settings |
|
| ||||
|
|
|
|
|
|
| 0 | 1 |
| 2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 0 |
| OFF | OFF |
| OFF |
|
|
|
|
|
| 1 |
| ON | OFF |
| OFF |
|
|
|
|
|
| 2 |
| OFF | ON |
| OFF |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 3 |
| ON | ON |
| OFF |
|
|
|
|
|
| 4 |
| OFF | OFF |
| ON |
|
|
|
|
|
| 5 |
| ON | OFF |
| ON |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 6 |
| OFF | ON |
| ON |
|
|
|
|
|
| 7 |
| ON | ON |
| ON |
|
|
| ||||||||||
KEY | Used to prevent the SCSI bus interface connector | ||||||||||
| from being plugged in upside down. |
|
| ||||||||
|
|
|
|
|
|
|
|
|
| ||
PREVENT/ |
| ON: |
| Allows insert and removal of a CD caddy | |||||||
ALLOW |
|
|
|
| with the eject button and the eject | ||||||
|
|
|
|
| command. |
|
|
|
|
| |
|
| OFF: Prevents insert and removal of a CD | |||||||||
|
|
|
|
| caddy with the eject button or an eject | ||||||
|
|
|
|
| command. |
|
|
|
|
| |
|
|
|
|
|
|
|
| ||||
TEST MODE |
| ON: | Enables test mode. |
|
|
|
| ||||
|
| OFF: | Enables normal operation. |
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
Factory settings
N o t e s :
•The upper row of pins (without KEY position) is ground.
•ID SELECT, PREVENT/ALLOW, and TEST MODE are recog- nized when the power supply is turned on or SCSI bus is reset.
•TEST MODE is used exclusively for the factory testing. Do not set TEST MODE to ON. Doing so may cause an unexpected result.
*AMP is a registered trademark of AMP, Inc.
**JAE is a registered trademark of Japan Aviation Electronics Industry, Ltd.
Installing the Drive Unit into the Computer | 11 |