Advanced menu page 3

a) For DSR-370P/570WSP: EBU75

Item

Settings

 

 

 

 

 

 

AWB MEM

2 (normal value): No

 

 

Selects whether or not

correspondence with FILTER

 

 

to make the FILTER

control settings. Only two

 

 

control settings (1 to 4)

adjustment values (A and B) are

 

 

correspond to

stored in memory.

 

 

separate white

2 ⋅ 4FL: Correspondence with

 

 

balance adjustment

FILTER control settings. Each of

 

 

values stored in

the four control settings can be

 

 

memory.

used to set A and B adjustment

 

 

 

values, for a total of eight settings.

 

 

 

 

 

 

TONE

ON (normal value): Outputs

 

 

Selects whether or not

audio signal.

 

 

to output a 1-kHz

OFF: Does not output audio

 

 

audio signal with the

signal.

 

 

color bars when the

 

 

 

OUTPUT/DL/DCC+

 

 

 

has been set to

 

 

 

BARS.

 

 

 

BARS

SMPTE (normal value for DSR-

 

 

Selects normal width

370/570WS): Normal width

 

 

or narrower width for

EBU75 (normal value for DSR-

 

 

color bars.

370P/570WSP): EBU 75%

 

 

 

EBU100 (for DSR-370P/

 

 

 

570WSP): EBU 100%

 

 

 

 

 

 

 

SPLIT (for DSR-370P/570WSP):

 

 

 

 

 

 

 

Not for normal operation

 

 

 

 

 

 

 

 

 

SNG: Narrower than normal (used

 

 

 

 

 

 

 

 

 

for satellite communications, etc.)

 

 

 

 

 

 

 

 

 

 

REMOTE1

REC (normal value): Specifies

 

 

 

 

 

Sets a function for

recording start/stop.

 

4Chapter

REMOTE connector 1.

CUE: Specifies a Cue point.

 

switch 1 of the RM-

MARK: Specifies a Mark IN/OUT

 

 

LG1 connected to the

point.

 

Viewfinder

 

NG: Specifies NG/OK.

 

 

 

 

REMOTE2

REC: Specifies recording start/stop.

 

 

Sets a function for

MARK (normal value): Specifies

 

 

switch 2 of the RM-

a Mark IN/OUT point.

 

Screen

LG1 connected to the

CUE: Specifies a Cue point.

 

 

 

REMOTE connector 1.

NG: Specifies NG/OK.

 

Indications

 

 

 

computer connected

9600, 38400 (normal value)

 

BAUD RATE

 

 

Sets a baud rate for a

 

 

 

to the REMOTE

 

 

and

connector 2 (to be

 

 

 

 

Menus

version).

 

 

supported in the future

 

 

 

 

 

 

 

iLINK CTL

REC/P (normal value): When an

 

 

Selects whether to

external VCR is recording or

 

 

control from the

recording paused, control from the

 

 

camera the start and

camera according to the setting of

 

 

stop of recording by

the VTR TRIGGER switch.

 

 

the external VCR

ALL: When an external VCR is

 

 

connected to the DV

 

 

recording, recording paused, or

 

 

OUT connector.

 

 

stopped, control from the camera

 

 

 

 

 

 

according to the setting of the VTR

 

 

 

TRIGGER switch.

 

 

 

For the DSR-1500/1500P/1600/

 

 

 

1600P/1800/1800P/2000/2000P,

 

 

 

which cannot be set to recording

 

 

 

paused, set this item to ALL.

 

 

 

OFF: Do not control from the

 

 

 

camera.

 

 

Chapter 4 Viewfinder Screen Indications and Menus 101