Note

You cannot enjoy a picture with an S video signal if your TV does not conform to the S video signal. When your TV does not have an S VIDEO input, connect the component via the VIDEO INPUT connector using the video connecting cord (not supplied) instead of the S video cord. For details, see page 8.

Refer to the instructions supplied with your TV.

Setups for the player when using the

digital connecting cords

Connect the component via the DIGITAL OUT OPTICAL or COAXIAL connector using an optical or coaxial digital connecting cord (not supplied). You do not need to use the audio connecting cord.

Some setup adjustments are necessary for the player depending on the components to be connected.

Use the setup display to change the various settings. For details on using the setup display, see page 46.

If your receiver (amplifier) does not have a builtin Dolby* Digital decoder, MPEG decoder or DTS decoder

•To listen to the sound through speakers connected to a receiver (amplifier) which has a digital connector, or to output the sound to a digital component such as a DAT or MD deck

Set the “AUDIO SETUP” items in the setup display (page 56) as shown in the illustration below. These are the default settings.

AUDIO SETUP

 

 

 

 

AUDIO ATT:

 

OFF

 

 

AUDIO DRC:

 

STANDARD

 

 

CENTER SPEAKER EQ:

FLAT

 

 

DOWNMIX:

DOLBY SURROUND

 

 

DIGITAL OUT:

 

ON

Set the

 

DOLBY DIGITAL:

 

D-PCM

 

MPEG:

 

PCM

items as

 

DTS:

 

OFF

shown

 

48kHz/96kHz PCM:

48kHz/16bit

 

To set, press , then ENTER .

To quit, press DISPLAY .

When you have made the connections using an optical or coaxial digital connecting cord, do not set “DOLBY DIGITAL” to “DOLBY DIGITAL,” “MPEG” to “MPEG,” “DTS” to “ON” and “48kHz/96kHz PCM” to “96kHz/24bit.” If you do, a loud noise will suddenly come out from the speakers, affecting your ears or causing the speakers to be damaged.

Note

You cannot make direct digital audio recordings of discs recorded in multichannel surround format using an MD deck or DAT deck.

If you have an audio component with a built-in Dolby Digital decoder, MPEG decoder or DTS decoder

•When you connect an audio component with a built- in Dolby Digital decoder A

Set “DIGITAL OUT” in “AUDIO SETUP” to “ON” and then set “DOLBY DIGITAL” to “DOLBY DIGITAL” in the setup display (page 57).

•When you connect an audio component with a built- MPEG decoder B

Set “DIGITAL OUT” in “AUDIO SETUP” to “ON” and then set “MPEG” to “MPEG” in the setup display (page 57).

•When you connect an audio component with a built- in DTS decoder C

Set “DIGITAL OUT” in “AUDIO SETUP” to “ON” and then set “DTS” to “ON” in the setup display (page 57).

AUDIO SETUP

 

 

 

 

AUDIO ATT:

 

OFF

 

 

AUDIO DRC:

 

STANDARD

 

 

CENTER SPEAKER EQ:

FLAT

 

 

DOWNMIX:

DOLBY SURROUND

A

 

DIGITAL OUT:

 

ON

 

DOLBY DIGITAL:

DOLBY DIGITAL

B

 

MPEG:

 

MPEG

 

DTS:

 

ON

 

 

48kHz/96kHz PCM:

48kHz/16bit

C

 

 

 

 

To set, press , then ENTER .

To quit, press DISPLAY .

Notes

•When you do not connect an audio component with a built-in Dolby Digital decoder, do not set “DOLBY DIGITAL” to “DOLBY DIGITAL.”

•When you do not connect an audio component with a built-in MPEG decoder, do not set “MPEG” to “MPEG.”

•When you do not connect an audio component with a built-in DTS decoder, do not set “DTS” to “ON.”

•When you connect the component via the DIGITAL OUT OPTICAL or COAXIAL connector, the Virtual 3D Surround effect cannot be heard.

*Manufactured under license from Dolby Laboratories. “Dolby,” “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories.

Confidential unpublished works. ©1992-1997 Dolby Laboratories. All rights reserved.

Started Getting

11