Sony HT-DDW700 56

Inputs (Analog)

SA-CD/CD, DVD,	Sensitivity: 800 mV
VIDEO 1, 2	Impedance: 50 kohms

Inputs (Digital)

DVD (Coaxial)	Sensitivity: –
	Impedance: 75 ohms

VIDEO 2 (Optical)	Sensitivity: –
	Impedance: –

Reproduction frequency range:
	28 – 20,000 Hz
Tone

Gain levels	±6 dB, 1 dB step

FM tuner section

Tuning range	87.5 - 108.0 MHz
Antenna	FM wire antenna
Antenna terminals	75 ohms, unbalanced
Intermediate frequency	10.7 MHz

AM tuner section

Tuning range

Models of area code U, CA

With 10-kHz tuning scale: 530 – 1,710 kHz3)

With 9-kHz tuning scale: 531 – 1,710 kHz3)

3)You can change the AM tuning scale to 9 kHz or 10 kHz. After tuning in any AM station, turn off the receiver. While holding down DIMMER, press ?/1. All preset stations will be erased when you change the tuning scale. To reset the scale to 10 kHz (or 9 kHz), repeat the procedure.

General

Power requirements

Area code	Power requirements
U, CA	120 V AC, 60 Hz

Power consumption

Area code	Power consumption

U	210 W

CA	290 VA

Power consumption (during standby mode)
	0.2 W
Dimensions (w/h/d) (Approx.)
	17 × 5 6/8 × 12 1/8 inches
	including projecting parts
	and controls
Mass (Approx.)	16 lb 9 oz

Speaker section

Front speakers (SS-MSP700) Center speaker (SS-CNP700) Surround speakers (SS-SRP700)

Front/center speakers	Full range, magnetically
	shielded
Surround speakers	Full range
Speaker units	70 mm cone type
Enclosure type	Close type
Rated Impedance	6 ohms
Dimension (w/h/d) (Approx.)
Front/surround speakers	3 5/8 × 3 7/8 × 4 inches
Center speaker	6 × 3 7/8 × 4 inches
Mass (Approx.)
Front speakers	1 lb 6 oz
Center speaker	1 lb 9 oz
Surround speakers	1 lb 2 oz

Sub woofer (SS-WP700)

Speaker system	Magnetically shielded
Speaker unit	200 mm cone type
Enclosure type	Bass reflex
Rated Impedance	6 ohms
Dimensions (w/h/d) (Approx.)
	10 6/8 × 13 × 12 inches
	including front panel
Mass (Approx.)	11 lb 8 oz

56US

Contents

Page WARNING For customers in the United States CAUTION Note to CATV system installer: About This Manual Table of Contents Getting Started Enjoying Surround Sound Tuner Operations Amplifier Operations Front panel About the indicators on the display Page Rear panel Remote commander Page Page 1: Installing speakers Installing the speakers on a flat surface Installing the speakers on the speaker stand Installing the speakers on the wall 3 Hang the speakers on the screws To connect the speakers correctly 3: Connecting the audio/video components How to hook up your components Audio input jack to be connected DigitalAnalog High quality sound Connecting audio components If you connect a DVD recorder 4: Connecting the antennas 5:Preparing the receiver and the remote 6:Calibrating the appropriate settings automatically Performing Auto Calibration Press AUTO CAL Error codes To rectify the error Error code and remedies Warning codes To change the settings manually Warning code and solution To turn off the test tone To mute the sound To avoid damaging your speakers Adjust to a suitable volume Playback the disc Turn on the receiver Listening/Watching a component Listening to a Super Audio CD/CD Watching a DVD 1 Turn on the TV and DVD player 2 Turn on the receiver 3 Press DVD 4 Switch the input of the TV so that an image of the DVD is displayed To return to the previous display To exit the menu Overview of the menus Page LEVEL menu parameters TONE menu parameters SUR menu parameters TUNER menu parameters AUDIO menu parameters SYSTEM menu parameters xSL DIST. (Surround left speaker distance) xSR DIST. (Surround right speaker distance) xSUR POS (Surround speaker position) xDIMMER (Brightness of the display) Enjoying Dolby Digital and DTS Surround sound Types of A.F.D. mode Selecting a preprogrammed sound field Types of sound field available About DCS (Digital Cinema Sound) About CINEMA STUDIO EX modes To turn off the surround effect for movie/music Using only the front speakers and sub woofer (2CH STEREO) Press 2CH Resetting sound fields to the initial settings 1 Press ?/1 to turn off the receiver In case of poor FM stereo reception If you cannot tune in a station 3 Press MEMORY 4 Press the numeric button to select the preset station 5 Press ENTER 6 Repeat steps 1 to 5 to preset another station Tuning to preset stations To create an index name Naming inputs Audio input modes All inputs except the FM and AM band FM and AM band Changing button assignments Categories and the corresponding buttons To clear all remote button assignments Glossary xDolby Digital xDolby Pro Logic xDolby Surround (Dolby Pro Logic) xDTS Digital Surround On safety On power sources On heat buildup On placement On operation If color irregularity is observed again If howling occurs On cleaning Page Remote control Error messages If you are unable to remedy the problem using the troubleshooting guide If the problem persist Reference sections for clearing the receiver’s memory Page Page Index Numerics