Sony HTSS1000P 10

Name Function

RControl After pressing AMP MENU

buttons (D), DVD MENU (J), or

MENU (N), press the control button V, v, B or b to select the settings. When you press DVD MENU or MENU, press the control button to enter the selection.

S DISPLAY		Press to
		– select information displayed
		on the receiver’s display (for
		TUNER input only).
		– select information displayed
		on the TV screen of the
		VCR, satellite tuner, CD
		player, DVD player, or MD
		deck.

T -/--		Press -/-- and TV (P) at the
		same time to select the
		channel entry mode, either
		one or two digits of the TV.

	>10/x	Press to select
		– track numbers over 10 of the
		VCR, satellite tuner, CD
		player or MD deck.
		– channel numbers of the
		Digital CATV terminal.

	CLEAR	Press to
		– clear a mistake when you
		press the incorrect numeric
		button.
		– return to continuous
		playback, etc. of the satellite
		tuner or DVD player.

Name Function

YTV/VIDEO Press TV/VIDEO and TV

(P) at the same time to select the input signal (TV input or video input).

SLEEP	Press to activate the Sleep
	Timer function and the
	duration which the receiver
	turns off automatically.

a)The number 5, MASTER VOL +, TV VOL +, and H buttons have tactile dots. Use the tactile dots as references when operating the receiver.

Notes

•Some functions explained in this section may not work depending on the model.

•The above explanation is intended to serve as an example only. Therefore, depending on the component, the above operation may not be possible or may operate differently than described.

UNumeric

buttons (number 5a))

Press to

–preset/tune to preset stations.

–select track numbers of the CD player, DVD player or MD deck. Press 0/10 to select track number 10.

–select channel numbers of the VCR or satellite tuner.

Press the numeric buttons and TV (P) at the same time to select the TV channels.

V 2CH	Press to select 2CH STEREO
	mode.

WA.F.D. Press to select A.F.D. mode.

XAUTO CAL Press to activate the Auto Calibration function.

10GB

Contents

Page WARNING About This Manual Table of Contents Description and location of parts Front panel About the indicators on the display Page Rear panel RM-AAU006 Page Page 1: Installing speakers Example of front speaker Installing the speakers on the wall 2 Fasten the screws to the wall. The screws should protrude 5 to 7 mm 3 Hang the speakers on the screws 2: Connecting speakers Notes on speaker cords Note on speakers 3: Connecting the audio/video components Component to be connected Connecting audio components If you connect a DVD recorder 4: Connecting the antennas 5:Preparing the receiver and the remote 6:Calibrating the appropriate settings automatically Performing Auto Calibration Press AUTO CAL Error codes To rectify the error Error code and remedies Warning codes To change the settings manually 7: Adjusting the speaker levels and balance To turn off the test tone Selecting a component To mute the sound To avoid damaging your speakers Listening/Watching a component Watching a DVD 1 Turn on the TV and DVD player 2 Turn on the receiver 3 Press DVD 4 Switch the input of the TV so that an image of the DVD is displayed Navigating through menus To return to the previous display To exit the menu Overview of the menus Page Adjusting the level LEVEL menu parameters Adjusting the tone TONE menu parameters Settings for the surround sound SUR menu parameters Settings for the tuner TUNER menu parameters Settings for the audio AUDIO menu parameters Settings for the system SYSTEM menu parameters xSL DIST. (Surround left speaker distance) xSR DIST. (Surround right speaker distance) xSUR PL (Surround speaker placement) Enjoying Dolby Digital and DTS Surround sound Types of A.F.D. mode Selecting a preprogrammed sound field Types of sound field available About DCS (Digital Cinema Sound) About CINEMA STUDIO EX modes To turn off the surround effect for movie/music Using only the front speakers and sub woofer Listening to FM/AM radio In case of poor FM stereo reception If you cannot tune in a station Storing FM stations automatically Presetting radio stations Using the controls on the receiver Displaying RDS information While receiving an RDS station, press DISPLAY repeatedly Description of program types Using the Sleep Timer Changing button assignments Categories and the corresponding buttons Glossary To clear all remote button assignments Precautions On safety On power sources On heat buildup On placement On operation If you encounter color irregularity on a nearby TV screen If color irregularity is observed Troubleshooting Remote control Error messages If you are unable to remedy the problem using the troubleshooting guide If the problem persist Reference sections for clearing the receiver’s memory Specifications Page Index