Manuals / Brands / Home Audio / Home Theater System / Sony / Home Audio / Home Theater System

Sony HTSS1000P Error codes, To rectify the error, Error code and remedies, Warning codes, To change the settings manually

1 56

Download 56 pages, 1.64 Mb

Error and warning codes

Error codes

When an error is detected during Auto Calibration, an error code will appear on the display cyclically after each measurement process as follows:

Error code t blank display t (error code t blank display)a) t PUSH t blank display

tENTER

a)Appears when there are more than one error code.

To rectify the error

1Record down the error code.

2Press the control button.

3Press ?/1 to turn off the receiver.

4Rectify the error.

For details, see “Error code and remedies” below.

5Turn on the receiver and perform Auto Calibration again (page 21).

Error code and remedies

Error	Explanation	Remedies
code

ERROR 10	The environment	Make sure the
	is too noisy.	environment is
		quiet during Auto
		Calibration.

ERROR 11 The speakers are		Place your speakers
	placed too near	further away from
	the optimizer	the optimizer
	microphone.	microphone.

ERROR 20	Front speakers	Check the front
	are not detected	speaker
	or only one front	connection.
	speaker is
	detected.

ERROR 21	Only one	Check the surround
	surround speaker	speaker
	is detected.	connection.

Warning codes

During Auto Calibration, the warning code provides information on the measurement result. The warning code will appear on the display cyclically as follows:

Warning code t blank display t (warning code t blank display)b) t PUSH t blank display t ENTER

b)Appears when there are more than one warning code.

You can choose to ignore the warning code as the Auto Calibration function will automatically adjust the settings. You can also change the settings manually.

To change the settings manually

1Record down the warning code.

2Press the control button.

3Press ?/1 to turn off the receiver.

4Follow the solution provided in the “Warning code and solution” below.

5Turn on the receiver and perform Auto Calibration again (page 21).

22GB

Contents

Page WARNING About This Manual Table of Contents Description and location of parts Front panel About the indicators on the display Page Rear panel RM-AAU006 Page Page 1: Installing speakers Example of front speaker Installing the speakers on the wall 2 Fasten the screws to the wall. The screws should protrude 5 to 7 mm 3 Hang the speakers on the screws 2: Connecting speakers Notes on speaker cords Note on speakers 3: Connecting the audio/video components Component to be connected Connecting audio components If you connect a DVD recorder 4: Connecting the antennas 5:Preparing the receiver and the remote 6:Calibrating the appropriate settings automatically Performing Auto Calibration Press AUTO CAL Error codes To rectify the error Error code and remedies Warning codes To change the settings manually 7: Adjusting the speaker levels and balance To turn off the test tone Selecting a component To mute the sound To avoid damaging your speakers Listening/Watching a component Watching a DVD 1 Turn on the TV and DVD player 2 Turn on the receiver 3 Press DVD 4 Switch the input of the TV so that an image of the DVD is displayed Navigating through menus To return to the previous display To exit the menu Overview of the menus Page Adjusting the level LEVEL menu parameters Adjusting the tone TONE menu parameters Settings for the surround sound SUR menu parameters Settings for the tuner TUNER menu parameters Settings for the audio AUDIO menu parameters Settings for the system SYSTEM menu parameters xSL DIST. (Surround left speaker distance) xSR DIST. (Surround right speaker distance) xSUR PL (Surround speaker placement) Enjoying Dolby Digital and DTS Surround sound Types of A.F.D. mode Selecting a preprogrammed sound field Types of sound field available About DCS (Digital Cinema Sound) About CINEMA STUDIO EX modes To turn off the surround effect for movie/music Using only the front speakers and sub woofer Listening to FM/AM radio In case of poor FM stereo reception If you cannot tune in a station Storing FM stations automatically Presetting radio stations Using the controls on the receiver Displaying RDS information While receiving an RDS station, press DISPLAY repeatedly Description of program types Using the Sleep Timer Changing button assignments Categories and the corresponding buttons Glossary To clear all remote button assignments Precautions On safety On power sources On heat buildup On placement On operation If you encounter color irregularity on a nearby TV screen If color irregularity is observed Troubleshooting Remote control Error messages If you are unable to remedy the problem using the troubleshooting guide If the problem persist Reference sections for clearing the receiver’s memory Specifications Page Index