Manuals / Brands / Home Audio / Home Theater System / Sony / Home Audio / Home Theater System

Sony HTSS1000P Specifications, If you are unable to remedy the problem using the troubleshooting guide, If the problem persist

1 56

Download 56 pages, 1.64 Mb

If you are unable to remedy the problem using the troubleshooting guide

Clearing the receiver’s memory may remedy the problem (page 19). However, note that all memorized settings will be reset to their factory settings and you will have to readjust all settings on the receiver.

If the problem persist

Consult your nearest Sony dealer.

Reference sections for clearing the receiver’s memory

To clear	See
All memorized settings	page 19

Customized sound fields	page 41

Specifications

Amplifier section

Power Output1)

Stereo mode (rated)	70 W + 70 W
	(4 ohms at 1 kHz, 0.7%)
Music power output (reference)
	FRONT2): 143 W/ch
	(With SS-MSP1000)
	CENTER2): 143 W
	(With SS-CNP1000)
	SUR2): 143 W/ch
	(With SS-SRP1000)
	SUBWOOFER2): 285 W
	(With SS-WP1000)
1)Measured under the following conditions:
Area code	Power requirements

CEL, CEK	230 V AC, 50 Hz

2)Depending on the sound field settings and the source, there may be no sound output.

Inputs (Analog)

SA-CD/CD,	Sensitivity: 1 V
VIDEO 1, 2	Impedance: 50 kohms

Inputs (Digital)

DVD (Coaxial)	Sensitivity: –
	Impedance: 75 ohms

VIDEO 2, SA-CD/	Sensitivity: –
CD (Optical)	Impedance: –

Reproduction frequency range:
	28 – 20,000 Hz
Tone

Gain levels	±6 dB, 1 dB step

FM tuner section
Tuning range	87.5 - 108.0 MHz
Antenna	FM wire antenna
Antenna terminals	75 ohms, unbalanced

Intermediate frequency

10.7 MHz

continued

Information Additional

53GB

Contents

Page WARNING About This Manual Table of Contents Description and location of parts Front panel About the indicators on the display Page Rear panel RM-AAU006 Page Page 1: Installing speakers Example of front speaker Installing the speakers on the wall 2 Fasten the screws to the wall. The screws should protrude 5 to 7 mm 3 Hang the speakers on the screws 2: Connecting speakers Notes on speaker cords Note on speakers 3: Connecting the audio/video components Component to be connected Connecting audio components If you connect a DVD recorder 4: Connecting the antennas 5:Preparing the receiver and the remote 6:Calibrating the appropriate settings automatically Performing Auto Calibration Press AUTO CAL Error codes To rectify the error Error code and remedies Warning codes To change the settings manually 7: Adjusting the speaker levels and balance To turn off the test tone Selecting a component To mute the sound To avoid damaging your speakers Listening/Watching a component Watching a DVD 1 Turn on the TV and DVD player 2 Turn on the receiver 3 Press DVD 4 Switch the input of the TV so that an image of the DVD is displayed Navigating through menus To return to the previous display To exit the menu Overview of the menus Page Adjusting the level LEVEL menu parameters Adjusting the tone TONE menu parameters Settings for the surround sound SUR menu parameters Settings for the tuner TUNER menu parameters Settings for the audio AUDIO menu parameters Settings for the system SYSTEM menu parameters xSL DIST. (Surround left speaker distance) xSR DIST. (Surround right speaker distance) xSUR PL (Surround speaker placement) Enjoying Dolby Digital and DTS Surround sound Types of A.F.D. mode Selecting a preprogrammed sound field Types of sound field available About DCS (Digital Cinema Sound) About CINEMA STUDIO EX modes To turn off the surround effect for movie/music Using only the front speakers and sub woofer Listening to FM/AM radio In case of poor FM stereo reception If you cannot tune in a station Storing FM stations automatically Presetting radio stations Using the controls on the receiver Displaying RDS information While receiving an RDS station, press DISPLAY repeatedly Description of program types Using the Sleep Timer Changing button assignments Categories and the corresponding buttons Glossary To clear all remote button assignments Precautions On safety On power sources On heat buildup On placement On operation If you encounter color irregularity on a nearby TV screen If color irregularity is observed Troubleshooting Remote control Error messages If you are unable to remedy the problem using the troubleshooting guide If the problem persist Reference sections for clearing the receiver’s memory Specifications Page Index