Sony ICF-C777 operating instructions A

If the power of the desired
component does not turn off, a long
beep sounds instead.
The infrared ray signals are not successfully
transmitted to the component from the current
location of the Dream Machine. Relocate the
Dream Machine to an optimal location where the
desired component is within the effective range
of the infrared rays and is free from obstructions.
After relocating the Dream Machine, repeat steps
1 to 4 once again.
To check the remote control
function
TV unit: Select TV and press REMOTE POWER.
If a compatible signal for your TV
unit is transmitted, your TV unit will
turn on.
Cable or VCR unit: Select CABLE/VCR and
press REMOTE POWER.
If a compatible signal for your cable
or VCR unit is transmitted,
your cable or
VCR unit will turn on.
TV and cable or VCR units: Select TV+CABLE/
VCR and press REMOTE POWER.
If a compatible signal for your TV and
cable or VCR units is transmitted, your
TV and cable or VCR units will turn on
at the same time.
Setting the Clock
and the Date
Setting the Clock
1 Plug in the unit.
“AM 12:00” flashes in the display.
2While holding down CLOCK, press
TIME SET+,– repeatedly until the
correct time appears in the display.
When you release CLOCK, the clock begins
to operate.
•To set the current time rapidly, keep pressing
the + or – button while holding down CLOCK.
Setting the Date
1While holding down SNOOZE/DATE/
SLEEP OFF, press TIME SET+,–
repeatedly until the correct date
appears in the display. Then, release
SNOOZE/DATE/SLEEP OFF.
•To display the date, hold down SNOOZE/
DATE/SLEEP OFF. When you release SNOOZE/
DATE/SLEEP OFF, the display returns to the
current time.
Playing the Radio
1Press RADIO ON/SLEEP to turn on the
radio and adjust VOL.
2Select FM or AM, and tune in to the
desired station using the TUNING dial.
•To turn off the radio, press RADIO OFF.
•To improve radio reception
FM: Extend the FM wire antenna fully.
AM: Rotate the unit horizontally for optimum
reception. A ferrite bar antenna is built into
the unit.
Installing the
Battery
To keep an accurate time, your Dream Machine
requires one 6F22 (9V) battery (not supplied), in
addition to the house current. The battery keeps
the clock operating in the event of a power
interruption. Before setting the time on your
Dream Machine, open the lid at the bottom of the
unit, install the battery with the correct polarity
and then close the lid.
Note
After a power interruption, the displayed time
may not be always correct. (It may gain or lose
about 10 minutes per hour.)
To check when to replace the battery
To check the remaining battery power, unplug
the power cord from the wall outlet and plug it in
again after a few minutes. If the
displayed time is incorrect, replace the battery
with a new one.
Determining the
Optimal Location for
the Dream Machine
The Dream Machine employs an omnidirectional
infrared ray system which enables the flexible
positioning of the Dream Machine anywhere in
your room!
Read the following carefully and familiarize
yourself with the optimal location of the Dream
Machine.
Effective range of the infrared rays
(See ill. A)
The effective range of the infrared rays emitted
from the infrared dome of the Dream Machine is
approximately 5 m (16 ft.) with a vertical angle of
approximately 40°. Make sure to place your TV,
cable or VCR unit so that the infrared ray sensors
are located within this range.
Notes on optimal location
•Place the Dream Machine in an area with a
direct line of sight from your TV, cable or VCR
unit. Remove any object that might obstruct the
direct line between the infrared dome of your
Dream Machine and the infrared ray sensor.
•Do not place the Dream Machine in an area
subject to direct sunlight or under any strong
illumination. The ominidirectional infrared ray
system may not operate properly.
•Do not use any other infrared ray remote
control device simultaneously with the Dream
Machine. An interference may occur and the
unit may not operate properly.
Setting Up the
Remote Control
Function
Complete this built-in pre-programmed ON/OFF
remote control setup before you proceed to the
next section. This will enable the successful
remote control of your TV, cable or VCR unit
from your Dream Machine.
The built-in pre-programmed remote control
setup will guide you in determining the
compatible infrared ray signal for your TV, cable
or VCR unit.
1Turn on the power of the desired
component (your TV, cable or VCR
unit) you wish to control remotely.
2Select TV or CABLE/VCR accordingly.
3Press REMOTE POWER on the Dream
Machine.
If the power of the desired component turns
off, you have successfully completed
the built-in pre-programmed ON/OFF
remote control setup.
If not, proceed to the next step.
4While holding down REMOTE POWER,
press BRAND SELECT.
If the power of the desired component turns
off, you have successfully completed the
built-in pre-programmed ON/OFF remote
control setup.
If not, repeat this step until the power of the
desired component turns off.
Top view
Side view
Setting the Alarms
The Dream Machine features a dual alarm to
enable the setting of Alarm A (remote) and
Alarm B (radio or buzzer).
Setting Alarm A
(Remote)
To set your TV, cable or VCR unit, first select the
desired channel and adjust the volume.
Before you proceed, make sure you have
successfully completed “Setting Up the Remote
Control Function".
1Select TV, CABLE/VCR or TV + CABLE/
VCR.
2While holding down ALARM A, press
TIME SET+,– until the desired time
appears in the display.
When ALARM A is released, the ALARM A
indicator and “:” will stop flashing and light
up. The current time will appear in the
display. The remote function will activate the
desired components at the preset time and
turn off automatically after 59 minutes.
Notes
• When Alarm A is set, the simultaneous use of
any other infrared ray remote control device
with the Dream Machine may lead to an
interference and the unit may not operate
properly.
• When your TV or VCR unit is on at the preset
time of Alarm A, your TV or VCR unit may
turn off inadvertently depending on the model.
Setting Alarm B
(Radio or Buzzer)
To set the radio, first tune in to the desired
station and adjust the volume.
1Select RADIO or BUZZER.
2While holding down ALARM B, press
TIME SET+,– until the desired time
appears in the display.
When ALARM B is released, the ALARM B
indicator and “:” will stop flashing and light
up. The current time will appear in the
display. The alarm will be activated at the
preset time and turn off automatically after 59
minutes.
Notes
•To check the preset time, press ALARM A or
ALARM B.
•To turn off the alarm, press ALARM RESET/
OFF. The alarm will be activated at the preset
time on the next day.
•To doze for a few more minutes, press
SNOOZE/DATE/SLEEP OFF. The alarm will
turn off temporarily and will activate again
after approximately 6 minutes. You can repeat
this process as many times as you like.
•To cancel either alarm, while holding down
ALARM A or ALARM B, press ALARM RESET/
OFF.
•To adjust the radio alarm volume, turn VOL.
•If you set ALARM A and ALARM B at the same
preset time, ALARM A only is activated.
Setting the Sleep
Timer
You can enjoy falling asleep to the radio using
the built-in sleep timer that turns off the radio
automatically after a preset duration.
1Press RADIO ON/SLEEP repeatedly.
The radio turns on and will turn off
automatically after the preset duration has
elapsed.
Each time you press RADIO ON/SLEEP, the
time changes as follows.
90 min
Radio on
(Sleep timer off) 45 min
30 min
15 minRadio off
60 min
•To turn off the radio before the preset duration
has elapsed, press SNOOZE/DATE/SLEEP
OFF.
FM wire antenna
AC power cord
Infrared dome
Display window
Compatible TV, Cable
Box, and VCR Brands for
Remote Control
The following popular TV, cable box, and VCR
brands are compatible with the remote control
function of the Dream Machine.
TV
Sony
Admiral
(M. Wards)
Akai
AOC
Bell & Howell
(M. Wards)
Brocsonic
Centurion
Coronad
Craig
Croslex
Curtis Mathis
Daewoo
Daytron
Emerson
Fisher
General Electric
Goldstar
Hitachi
JC Penny
JVC
KTV
LXI (Sears)
Magnavox
Cable Box/VCR
Cable Box
Gemini
G.I.
Hamlin/Regal
Jerrold/G.I.
Macom
Magnavox
Oak
Panasonic
Philips
Pioneer
Scientific Atlanta
Samsung
Tocom
Zenith
VCR
Sony
Admiral
(M. Wards)
Aiwa
Audio Dynamic
Bell & Howell
(M. Wards)
Brocsonic
Canon
Citizen
Craig
Curtis Mathis
Daewoo
DBX
Dimensia
Emerson
Fisher
Funai
General Electric
Goldstar
Hitachi
Instant Replay
JC Penny
JVC
Kenwood
LXI (Sears)
Magnavox
Marantz
Marta
Memorex
Minolta
Mitsubishi/MGA
Multitech
NEC
Olympic
Panasonic
Pentax
Philco
Philips
Pioneer
Quasar
RCA/PROSCAN
Realistic
Sansui
Singer
Samsung
Sanyo
Scott
Sharp
Shintom
Signature 2000
(M. Wards)
Sylvania
Symphonic
Tashiro
Tatung
Teac
Technica
Technics
Toshiba
Wards
Yamaha
Zenith
•This Remote Commander may not operate
certain models of TVs, VCRs and Cable Boxes
of the manufacturers listed above.
•lf this Remote Commander does not operate
your TV, VCR or Cable Box after you have
attempted to set up the manufacturer's code,
please call 1-800-822-2217.
A
BRAND SELECT
REMOTE
POWER
TV
CABLE/VCR
TV+
CABLE/VCR
VOL
TUNING
AM FM
BAND
RADIO
BUZZER
RADIO/
BUZZER
REMOTE
ALARM
TIME SET
RADIO
OFF ON/SLEEP
ALARM RESET/OFF
CLOCK
SNOOZE/DATE/SLEEP OFF
20˚
20˚
20˚
20˚
Maranz
Mitsubishi/MGA
NEC
Panasonic
Philco
Philips
Pioneer
Portland
Quasar
Radio Shack
RCA/PROSCAN
Samsung
Sanyo
Sears
Scott
Sharp
Signature 2000
(M. Wards)
Sylvania
Symphonic
Toshiba
Videch
Wards
Zenith