• To use a learned function later, press the T or t buttons to select AUX and next press the relevant button.
• Always remember to press the T or t button until the green light iluminates according to the equipment you want to operate with this remote control: VCR, TV,
DVD or AUX.
continued...
MODE

Learning functions from other Remote Controls

To eliminate the amount of remote controls you need, this remote control has a learning feature. Once set up as explained below, it can be used in place of your other remote controls.

It is recommended that you make a note of what each button has been taught (you can use the table provided with the remote control).

Before you start and for accurate learning, please read below instructions:

•Choose the button (a-g) you want to learn. See fig. 3 to find out the possible buttons.

•Do not move the remote units during the learning procedure.

•Be sure to keep holding down the learning button until your commander reacts as described.

•Use fresh batteries in both remote units.

•Avoid learning in places subjects to direct sunlight or a strong fluorescent light.

•Noise may interfere during the learning procedure.

•The remote control detector area may differ depending on each remote unit. If learning does not work, try changing the positions of the two remote controls.

•It is possible that some specific remote control signals may not be learned.

•If you do not perform the learning steps within 20 seconds at any point during the process, the learning mode ends.

fig. 3

Buttons available to

store learned

functions.

a

AUX/VIDEO

13

b 4 6

79

c

d

e

f

fig. 1

2-3 cm.

1

Position both remote controls as shown (see fig. 1).

 

 

 

 

 

2

Press and hold the t button of this TV remote control for

 

 

 

 

 

 

approximately 6 seconds, until the green AUX light starts flashing

 

 

 

This TV remote

 

Other remote

 

(see fig.2).

control

 

 

control

 

 

 

 

3

 

fig. 2

Press the button on this TV remote control that you wish to use to

 

 

 

 

 

 

 

store a learned function (see fig.3).

 

V

D

 

 

 

V

 

 

T

 

D

 

 

C

R

 

A

 

 

 

U

 

 

 

 

 

X

 

Once the selected button has been pressed, the VCR, TV, DVD and

V

 

 

 

 

 

 

 

 

 

 

AUX lights illuminate in order (see fig. 4).

MODE

 

6 sec.

4Press the button on the other remote control that you wish to teach your TV

g

remote control.

 

 

fig. 4

 

• During the data transfer process, all the four lights illuminate at the

 

 

 

 

 

same time (see fig. 5).

 

 

V

DV

 

• As soon as data transfer is finished, the AUX green light starts

 

R

T

D

 

C

 

U

 

 

 

X

 

 

 

 

 

A

 

flashing (see fig. 6).

V

 

 

 

 

 

 

MODE

 

 

 

 

5If you wish to record other functions repeat steps 2-4 (read before the

warning below), otherwise go to step 6.

 

fig. 5

• In case you try to select one button which has been already

 

V

DV

learned, all the four lights will momentarily flash very shortly and

 

T

 

D

C

R

 

U

 

 

X

 

 

 

 

A

the remote control automatically return to the same condition as

V

 

 

 

 

MODE

in the step 2 with the AUX light flashing

 

 

 

 

 

• In case you try to select a not-learnable button, the remote control

 

fig. 6

stay in to the same condition as in the step 2 with the AUX light

 

flashing.

 

V

D

 

 

 

V

 

 

T

 

D

 

 

R

 

U

6 Press the t button to finish the learning process.

C

 

 

A

 

 

X

V

 

 

 

 

 

 

 

7Check that all the learning functions have been learned correctly.

42 Additional Information