Manuals / Brands / TV and Video / Universal Remote / Sony / TV and Video / Universal Remote

Sony RM-VL1000 Notes on learning the signals of an air- conditioner, About seasonal adjustments

1 84

Download 84 pages, 876.88 Kb

Using Non-Preset Remote Control Operations

—Learning Function (continued)

If you make a mistake, move the cursor to the digit or character you want to correct by pressing the or button, and input again.

4Decide the digit or the character you input by pressing the Joystick toward .

The cursor moves to the right. When the Joystick is pressed toward , the cursor moves to the left. You can input a digit or character to the place where the cursor flashes.

5Repeat Steps 3 and 4 until you input a suitable name to the label.

When the cursor reaches to the right end, if the Joystick is pressed toward , the cursor returns back to the left end.

6Press the SET button.

The commander enters the learning standby mode.

Notes on learning the signals of an air- conditioner

About seasonal adjustments

If you change the settings of the air-conditioner for the season, you have to program the remote control signals of the new settings on the Commander.

If the power-on/off operation does not work correctly

The air-conditioner may not be turned on or off properly with the button or key of this Commander, for which you have programmed its power-on/off signal.

If the Commander can operate only “ON” with one button or label and “OFF” with another, while your air-conditioner’s remote control can operate “ON/ OFF” with a single button or label, program the signal on two buttons or labels of the Commander as follows.

1Clear the learned power-on/off signal from the button or label (page 29).

2Program the signal (transmitted from the power-on/off button of the air-conditioner’s remote control) for the button or label again.

3Program the signal from the same button of the remote control for another button or label.

The two buttons or labels of the Commander have been programmed with the power-on signal and the power-off signal of the air-conditioner, respectively so that you can operate the air- conditioner with the Commander.

28

Contents

Page WARNING Features Table of Contents Getting Started Basic Operations Advanced Features Using Other Functions Additional Information Appendix Location and Function of Controls Installing the Batteries When to replace the batteries Setting the Clock Setting the clock for the first time after installing batteries MON Note Continued Setting the Clock (continued) 9:00 PM STD TIME Notes 9:30 PM 1,5 WED 10:00 AM STD TIMEDS TIME 10:00 AM Setting the Code for Preset Audio and Visual Components Setting a component code VCR1 VCR2 Example: To enter “8056” If the setting of the code is successful If you press the SET button Checking if the code number works Finding a component code with the Search function Page CH MACRO VOLUME POWER ON COPY ALL COMPLETE R R R Operating Your Components with the Remote Commander Operating Your Components with the Remote Commander (continued) ANT SW SEARCH t SEARCH T PLAYx2 COUNTER Using Non-Preset Remote Control Operations —Learning Function (continued) ANT SW SEARCH Note on the flashing display To change the name of the Labels When teaching to a label on the LCD When teaching to a button on the Commander When the command has been learned successfully If “NG” flashes on the display To learn another component’s remote control signal If you press the SET button once again If you want to set a component code to a label after learning a signal To change the function name of the labels on the display . t / t : t ? t ~ t t t t t t t t t t Notes on learning the signals of an air- conditioner For accurate learning Changing or erasing the function of a taught label or button Advanced Features Controlling the Volume of Visual Components Connected to an Audio System To change the Factory Preset of the Volume Control 5,7 3,6 1,8 VISUAL AUDIO Page Page Programming a series of commands for the System Macro labels SONY OFF SYSTEM2 SYSTEM3 SYSTEM4 Executing a Series of Commands —System Control Functions (continued) About the interval between operation steps About the order of operation steps To change the name of a System Macro label on the display Notes on System Control Operations To clear programmed commands for a specific System Macro number label If you want to erase the settings of other macro numbers Programming a series of commands for the component labels To clear the component macro of a label Continued Changing the interval between operation steps Page Adding an Extra Function to the Component Labels To clear the Power-Oncommand OFF Assigning Other Components to the Component Labels Copying the settings of a component label to another label To return to the original setting Selecting a Channel with a Single Label Page Selecting a Channel with a Single Label — Channel Macro Function (continued) To change the name of the Channel Macro labels on the display To clear the Channel Macro of a label If the character contents of the label have been changed Setting the Timer Setting the new timer program Setting the Timer (continued) ON/OFF TEST SETUP 12:00 AM MACRO EVERYDAY MON-SAT MON-FRI SUN SAT TUE 7:30 AM Page Page NG MacroCLR If you select “NG?” To check the execution of the timer program To switch the timer standby mode to on or off To switch quickly the timer standby mode to on or off using the TIMER button To clear timer settings programmed for a specific program number label Page Using Other Functions Locking the Controls —Hold Function LOCK Adjusting the Automatic-OffTime of the Backlight of the Display Window Setting the Key- Touch Beep Contrast of the Display Window Changing the Names of the Labels on the Display (continued) COMPO: LABEL If you want to change the name of the function label of each component SYSTEM: TIMER: Erasing All the Settings YES NO Precautions Maintenance Specifications Troubleshooting Troubleshooting (continued) For the customers in the U.S.A Customer Support Information Table of Preset Functions SAT (Digital Satellite) Digital cable box DVD VCR1, VCR2 DVR (Digital video recorder) CABLE (Cable box) AMP DAT TAPE A, TAPE B Index