Names and Functions

Front panel

1 2

3

4

 

 

5

6

7 8 9 0

!Á

 

MIC1 MIC2

MIC3

MIC4

ST1

ST2

ST3

 

 

 

 

 

 

 

 

 

 

 

 

 

ECHO RETURN

CLIP

PROTECTION

EMG

+45V

 

 

ECHO/

 

 

 

 

 

 

 

 

 

 

 

 

 

AUX SEND

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

¯ON ¿OFF

MUTING

 

MASTER VOLUME

 

 

 

 

RF/

RF/SIGNAL

SIGNAL

SIGNALSIGNAL

SIGNAL

 

 

 

 

 

SIGNAL

SIGNAL

 

 

 

 

 

 

 

 

 

 

 

¯ON ¿OFF

+10

 

+10

 

 

+10

 

 

 

 

 

 

 

 

+5

 

+5

 

 

+5

A

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0

 

0

 

 

0

B

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

-5

 

-5

 

 

-5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

C

 

 

 

 

 

 

 

-15

 

-15

 

 

-15

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MIC GROUP

BASS

TREBLE

BALANCE

MIC4

-25

 

-25

 

 

-25

D

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MIN MAX

MIN

MAX

L

R

 

 

 

 

PLAYER

PLAYER/RECORDER

 

 

 

 

 

 

 

 

!ª

!£

!¢

!°

!¤

!¦

!¥

!»

@¼

@Á

@ª

@£

1 POWER button

 

 

 

 

7 CLIP indicator

 

 

 

 

 

Pressing it turns on the power.

 

 

 

 

Too high an output level will cause signal distortion

 

 

 

 

 

 

and make the CLIP indicator light up. When this

2 Wireless remote control sensor

 

 

 

happens, lower the MASTER volume or the MIC/

It catches the signal from the infrared wireless remote

 

LINE level knob until the indicator turns off. If too

control.

 

 

 

 

 

much signal output for an extended period, it may

If this sensor is covered by something, the remote

 

 

cause the equipment to overheat or to damage the

control may not function correctly. Place the unit so

 

 

speakers.

 

 

 

 

 

 

that the sensor will be easy to receive the remote

 

8 PROTECTION indicator

 

 

control signal.

 

 

 

 

 

 

 

 

 

 

 

 

It lights up while the protection circuit is working.

3 ECHO/AUX SEND knob

 

 

 

 

When the power is turned on, it also lights up for few

It adjusts the mixed signals after each channel fader

 

 

seconds and it turns off when the amplifier become

and outputs to the ECHO SEND terminal.

 

 

 

stable.

 

 

 

 

 

 

 

4RF/SIGNAL indicators

They light up regardless of the position of channel fader when sound signal of more than -20dB to the standard input level are input.

As for MIC 1/MIC 2 would be light up when it received the signal while the wireless tuner unit is installed and switch of the microphone is turned on.

5ECHO RETURN switch

When it is ON, the signal from the ECHO RETURN input are assigned to L/R and Rec Bus.

6MUTING button

Use muting outputs from MASTER OUTPUT, MASTER INSERT, ECHO SEND, MIC GROUP OUT, and SPEAKER output terminals.

4

9EMG indicator

It lights up when the unit receives a signal from the emergency broadcast facilities and turns to standby. As for EMG, refer to P. 75.

0+48V indicator

It lights up while the Phantom power (DC+48V) is supplied through the MIC input terminal.

!Á MASTER VOLUME

Use to adjust the volume of MASTER OUTPUT and SPEAKER terminal.

!ª MIC 4 terminal

This is input terminal in front for wired microphone. If the wired microphones are connected to the MIC 4 terminals both at front and rear panel, the front input is given priority.

Note : When you use the MIC 4, check the balanced connection.