Sony STR-DN1010 , Performing Auto Calibration

107GB

D:\NORM'S JOB\SONY HA\SO0062\STR-DN1010\GB\GB05ENJ_STR-DN1010-CEL.fm masterpage: Right

STR-DN1010

4-174-068-11(1)

Advanced Operations

For details on the Auto Calibration, see

“Calibrating the appropriate speaker settings

automatically (Auto Calibration)” (page 38).

See “Before you perform Auto Calibration”

(page 38) before performing the Auto

Calibration.

To operate on the receiver

1Press GUI MODE repeatedly to select

“MENU OFF”.

2Press AMP.

Receiver operation is enabled.

3Press MENU.

4Press V/v repeatedly to select “<AUTO

CAL>” , then press or b.

5Press V/v repeatedly to select “A.CAL

START”, then press to start the

measurement.

Measurement starts in 5 seconds. A count

down is displayed.

Note

While the time is counting down, stand away

from the measurement area to avoid

measurement error.

6Measurement starts.

The measurement process will take

approximately 30 seconds. Wait until the

measurement process completes.

To cancel Auto Calibration

The Auto Calibration function will be

canceled when you do the following during the

measurement process:

– Press ?/1.

– Press the input buttons on the remote or

press the INPUT SELECTOR +/–

repeatedly on the receiver.

– Press MUTING (RM-AAP051 only) or

(RM-AAP052 only) on the remote. You can

also use MUTING on the receiver.

– Press SPEAKERS on the receiver.

– Change the volume level.

– Connect the headphones.

Tips

• Operations other than turning the receiver on or off

are deactivated during Auto Calibration.

• The measurements may not be performed correctly

or Auto Calibration cannot be performed when

special speakers, such as dipole speakers are used.

To confirm/save Auto

Calibration results when GUI

function is turned off

1Confirm the measurement result.

When the measurement ends, a beep

sounds and the measurement result appears

on the display.

a) xxx

represent a speaker channel.

FFront

S Surround

SB Surround back

FH Front high

Depending on the error code, the speaker

channel may not appears.

b)xx

represent an error code.

Performing Auto Calibration

Measurement process

[Display]

Explanation

Completes properly

[SAVE EXIT]

Proceed to step 2.

Fails

[

E -

xxx

a)

:

xx

b)

]

See “Message list

after Auto

Calibration

measurement”

(page 43).

continued

Contents

Main To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. For customers in the United States WARNING Owners Record Important Safety Instructions CAUTION For customers in Europe For customers in Australia About This Manual On copyrights Table of Contents Connections Preparing the Receiver Basic Operations Tuner Operations S-AIR Operations Advanced Operations Using the Remote Additional Information Supplied accessories Inserting batteries into the remote Description and location of parts Front panel Page About the indicators on the display x q z kq;qaqsqdqfqh qgqj Page Rear panel 1 2 43 8 76 6 5 AS-AIR section BDMPORT section Remote commander A B / cb)/C (RM-AAP052 only) Page To control other Sony components 1: Installing the speakers Example of speaker system configuration Connections Tips 2: Connecting the speakers Bi-amplifier connection 3: Connecting the TV 4a: Connecting the audio components Notes on connecting DIGITAL MEDIA PORT adapter To detach the DIGITAL MEDIA PORT adapter from DMPORT jack Page 4b: Connecting the video components If you want to connect several digital components, but cannot find an unused input Converting video signals Components to be connected Video input/output jacks to be connected Connecting components with HDMI jacks AHDMI cable (not supplied) Notes on connecting cables Notes on HDMI connections Connecting a Blu-ray disc player Connections The following illustration shows how to connect a DVD player or DVD recorder. Recommended connection Alternative connection Connecting a DVD player, DVD recorder AB Connecting a satellite tuner, cable TV tuner Connecting components with analog video and audio jack Function for conversion of video signals Notes on converting video signals To connect a recording component 5: Connecting the antennas (aerials) 6: Inserting the wireless transmitter/transceiver To insert the wireless transmitter into the S-AIR main 1 2 7: Connecting the AC power cord (mains lead) Initializing the receiver 1 2 Selecting the front speaker system Press SPEAKERS repeatedly to select the front speaker system you want to drive. Calibrating the appropriate speaker settings automatically (Auto Calibration) Before you perform Auto Calibration 1 microphone to the AUTO CAL MIC jack. 2 microphone. On setting up the active subwoofer 3 4 5 6 7 2: Performing Auto Calibration 1 result. 2 3 3: Confirming/saving the measurement results 4 Type. Press V/v repeatedly to select Auto Cal. Type, then press . 5 microphone after you have finished. When Error Code appears 1 2 3 When Warning appears Message list after Auto Calibration measurement Guide to on-screen display operation 2 Using the menu menu you want, then press . 3 2 menu you want, then press or b to enter the menu. 3 the menu item list is displayed. 4 Playback 2 3 4 5 1 Input screen to select the input you want. 3 Name Input, then press . 4 Enjoying sound/images from the components connected to the DIGITAL MEDIA PORT 2 3 4 To operate the TDM-iP50 or TDM-NC1 using the GUI menu of the receiver 1 2 Selecting the operation screen Operating the component connected to the DIGITAL MEDIA PORT adapter Contents list for audio Contents list for video 3 (RM-AAP051 only) or 2 +/ (RM-AAP052 only) to adjust the volume. To operate the TDM-iP50 using the iPod menu Playing the selected track 1 3 4 DIGITAL MEDIA PORT message list Selecting the playback mode Using the Sleep Timer Recording using the receiver Recording onto a CD-R 1 2 1 playback component. 2 component for playing. 3 2 3 4 In case of poor FM stereo reception 2 3 4 5 If you cannot tune in a station 1 2 3 Presetting FM/AM radio stations (Preset Tuning) 2 6 7 Receiving RDS broadcasts 1 2 Listening to Satellite Radio (Models of area code U2, CA2 only) Connecting the SIRIUS Satellite Radio Preparing to listen to the SIRIUS Satellite Radio Checking the SIRIUS Radio ID 2 3 2 3 4 Selecting a channel of the SIRIUS Satellite Radio 2 Checking receiving conditions (Antenna Aiming) Selecting a channel by category (Category Mode) 3 4 2 3 4 5 6 Selecting a channel by inputting the channel number directly (Direct Tuning) Presetting SIRIUS Satellite Radio channels 2 3 5 6 Restricting access to specific channels (Parental Lock) 1 lock using Category Mode (page 59) or Direct Tuning (page 60). 3 To listen to the locked channels 1 2 To cancel the Parental Lock 1 2 3 SIRIUS Satellite Radio message list Selecting the sound field 2 channel sound mode Press SOUND FIELD +/ repeatedly to select the sound field you want. x2CH ST. (2ch Stereo) xA. DIRECT (Analog Direct) Music mode xHP 2CH (HP (2 ch)) xHP DIRECT (HP (Direct)) If you connect a subwoofer To turn off the surround effect for movie/music When connecting Blu-ray disc players and other next generation HD players Enjoying the surround effect at low volume levels (NIGHT MODE) Press NIGHT MODE to select NIGHT ON. Resetting sound fields to the initial settings 1 What is BRAVIA Sync? Preparing for the BRAVIA Sync BRAVIA Sync Features If your TV is compatible with the Control for HDMI-Easy Setting function 1 If your TV is not compatible with the Control for HDMI-Easy Setting function 1 2 3 4 Playing back components with one-touch operation (One-Touch Play) Enjoying the TV sound from the speakers connected to the receiver (System Audio Control) Turning off the receiver with the TV (System Power Off) Press TV, then press AV ?/1. Enjoying movies with the optimum sound field (Theater/Theatre Mode Sync) Enjoying the TV sound via an HDMI cable (Audio Return Channel) 2 3 4 About S-AIR products S-AIR Operations Setting up an S-AIR product About environments where S-AIR products (S-AIR main unit and sub unit) are used To set the ID of the S-AIR main 1 2 3 Pairing the S-AIR main unit with a specific S-AIR sub unit (Pairing operation) To perform pairing 1 2 3 4 5 Enjoying the systems sound in another room 1 to match the ID of the S-AIR main unit. 2 3 8 S-AIR receiver. xWhen Party is set xWhen Separate is set 9 To control the system from the S-AIR receiver 4 RF Change, then press or b. When S-AIR reception is poor 5 the setting you want, then Enjoying the S-AIR receiver while the S-AIR main unit is in standby mode 2 3 4 S-AIR Stby, then press or b. 5 the setting you want. Advanced Operations Switching between digital and analog audio (INPUT MODE) Enjoying the sound/ images from other inputs 2 Input, then press or b. 3 the input name you want to assign. 5 6 7 Page Using a bi-amplifier connection 2 3 4 5 Using the setting menu 2 Settings, then press or b to enter the menu mode. 3 Auto Calibration menu Auto Cal. Start (Auto Calibration start) Auto Cal. Type (Auto Calibration type) Position To register settings for the listening environment Speaker Settings menu 1 2 3 SP Pattern (Speaker pattern) Manual Setup 1 2 3 To adjust the size of each 1 1 the speaker on the screen you want to adjust, then press . 2 the value, then press . To output test tone from each D.Range Comp (Dynamic range compression) xFEET xMETER Surround Settings menu S.F. Select (Sound field select) Distance Unit To select the surround sound field 1 2 EQ Settings menu To adjust the equalizer on the EQ screen 1 2 Audio Settings menu xMain/Sub Video Settings menu x480/576p x720p x1080i x1080p HDMI Settings menu Comp.Dec. (Component video decoder) Ctrl for HDMI (Control for HDMI) Pass Through xAMP xTV+AMP x+10 dB x0 dB Audio Out (Setting HDMI audio input) System Settings menu ARC (Audio Return Channel) Auto Standby Operating without connecting to a TV Using the menu in the display 1 2 3 4 5 Overview of the menus Page Page Page Page To operate on the receiver 1 2 3 4 5 2 3 4 5 When you select PHASE INFO. 1 want to preset. 2 MEMORY. 3 Listening to satellite tuner (Models of area code U2, CA2 only) 1 2 3 4 5 Programming the remote 1 2 3 4 If programming is unsuccessful, check the following: To control a tuner To control a CD player To control a DAT deck To control a tape deck The numeric codes corresponding to the component and the maker of the component To control an MD deck To control an HDD recorder To control a Blu-ray disc player/ recorder To control a PSX To control a DVD player To control a DVD recorder To control a DVD/VCR COMBO To control a DVD/HDD COMBO To control a TV Using the Remote To control an LD player To control a Video CD player To control a VCR To control a satellite tuner To control a cable box Clearing all the contents of the remotes memory 1 VOL (RM-AAP051 only) or 2 and hold ?/1, then press AV ?/1. The RM SET UP indicator flashes 3 times. Glossary xCinema Studio EX xComponent video xComposite video xCrossover frequency xDolby Digital Plus xDolby Digital Surround EX xDolby Pro Logic II xDolby Pro Logic IIx xDolby Pro Logic IIz xDTS-HD xDTS Neo:6 xHDMI (High-Definition Multimedia Interface) xHigh Bitrate Audio xInterlace Precautions On safety On power sources On heat buildup On placement On operation On cleaning On S-AIR function Troubleshooting Audio Page Video HDMI S-AIR function Tuner Remote commander Others Error messages Specifications AUDIO POWER SPECIFICATIONS (Models of area code U2 only) If you are unable to remedy the problem using the troubleshooting guide If the problem persist Reference sections for clearing the receivers memory FM tuner section AM tuner section Video section HDMI Video HDMI Video (3D) Page Index Numerics A B C