xSurround speaker height (SLSR)*

Initial setting : HGT. LOW

This parameter lets you specify the height of your surround speakers for proper implementation of the Digital Cinema Sound surround modes in the “VIRTUAL” sound fields. Refer to the illustration below.

•Select “HGT. LOW” if the location of your surround speakers corresponds to section A.

•Select “HGT. HIGH” if the location of your surround speakers corresponds to section B.

This setting only affects the surround modes in the “VIRTUAL” sound fields.

B B

 

60

A

A

 

30

*These parameters are not available when “Surround speaker size“ is set to “NO”.

zAbout the surround speaker position (PL. SIDE, PL. MID and PL. BEHD.)

This setting is designed specifically for implementation of the Digital Cinema Sound modes in the “VIRTUAL” sound fields. With the Digital Cinema Sound modes, speaker position is not as critical as other modes. All of the modes in the “VIRTUAL” sound fields were designed under the premise that the surround speaker would be located behind the listening position, but presentation remains fairly consistent even with the surround speakers positioned at a rather wide angle. However, if the speakers are pointing toward the listener from the immediate left and right of the listening position, the “VIRTUAL” sound fields will not be effective unless the surround speaker position parameter is set to “PL. SIDE”.

Nevertheless, each listening environment has many variables, such as wall reflections, and you may obtain better results using “PL. BEHD” or “PL. MID” if your speakers are located high above the listening position, even if they are to the immediate left and right.

Therefore, although it may result in a setting contrary to the “Surround speaker position” explanation, we recommend that you play back multi channel surround encoded software and listen to the effect each setting has on your listening environment. Choose the setting that provides a good sense of spaciousness and that best succeeds in forming a cohesive space between the surround sound from the surround speakers and the sound from the front speakers. If you are not sure which sounds best, select “PL. BEHD.” and then use the speaker distance parameter and speaker level adjustments to obtain proper balance.

xSub woofer selection

Initial setting : S.W. YES

• If you connect a sub woofer, select “S.W. YES”.

• If you do not connect a sub woofer, select “S.W. NO”. This activates the bass redirection circuitry and outputs the LFE signals from other speakers.

• In order to take full advantage of the Dolby Digital bass redirection circuitry, we recommend setting the sub woofer’s cut off frequency as high as possible.

xFront speaker distance ( L R )

Initial setting : DIST. 5.0 m (5.0 meter) 16 feet

Set the distance from your listening position to the front (left or right) speaker (A on page 15).

•Front speaker distance can be set in 1 foot (0.1 meter) steps from 3 to 40 feet (1.0 to 12.0 meters).

•If both speakers are not placed an equal distance from your listening position, set the distance to the closest speaker.

xCenter speaker distance ( C )

Initial setting : DIST. 5.0 m (5.0 meter) 16 feet

Set the distance from your listening position to the center speaker.

•Center speaker distance can be set in 1 foot (0.1 meter) steps from a distance equal to the front speaker distance (A on page 15) to a distance 5 feet (1.5 meters) closer to your listening position (B on page 15).

•Do not place the center speaker farther away from your listening position than the front speakers.

xSurround speaker distance (SLSR)

Initial setting : DIST. 3.5 m (3.5 meter) 11 feet

Set the distance from your listening position to the surround (left or right) speaker.

• Surround speaker distance can be set in 1 foot (0.1 meter) steps from a distance equal to the front speaker distance (A on page 15) to a distance 15 feet (4.5 meters) closer to your listening position (C on page 15).

• Do not place the surround speakers farther away from your listening position than the front speakers.

• If both speakers are not placed an equal distance from your listening position, set the distance to the closest speaker.

Up Hooking

Setting and the Up System Speaker

17