Specifications
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
50Ê watts per channel minimum continuous average power into 4Ê ohms, both channels driven from 20 Hz to 20 kHz with no more than 0.03% total harmonic distortion per Car Audio Ad Hoc Committee standards.
Other Specifications
Circuit system | OTL (output transformerless) | Frequency response | |
| circuit |
| 5 Hz – 100 kHz ( +0 dB) |
| pulse power supply |
| |
| Harmonic distortion | ||
Inputs | RCA pin jacks |
| 0.003 % or less |
Outputs | Speaker terminals |
| (at 1kHz, 4 ohms, 16 W) |
Speaker impedance | Input level adjustment range | ||
| 1 – 8 ohms (stereo) |
| 0.2 – 2 V |
| 2 – 8 ohms (when used as a | ||
| bridging amplifier) |
| 80 Hz, – 12 dB/oct |
Maximum output | |||
| 100 W per channel with |
| 50 Hz, 80 Hz, – 18 dB/oct |
| Power requirements | ||
| 200 W per channel with |
| 12 V DC car battery |
|
| (negative ground) | |
| 380 W per channel with | Power supply voltage | |
|
| 10.5 – 16 V | |
| 500 W per channel with | Current drain | at rated output: 27 A |
|
| (4 ohms, 40 W × 4) at 10 % | |
Rated outputs (supply voltage at 14.4 V) |
| THD: 32 A | |
| 50 W per channel with |
| Remote input: 5 mA |
| Dimensions | Approx. 230 × 60 × 360 mm | |
| kHz, 0.03 % THD, at 4 ohms) |
| (w/h/d) |
| 95 W per channel with |
| (9 1/8 × 2 3/8 × 14 1/4 in.) not incl. |
|
| projecting parts and controls | |
| kHz, 0.08 % THD, at 2 ohms) | Mass | Approx. 4.6 kg (10 lb. 7 oz.) not |
| 125 W per channel with |
| incl. accessories |
| Supplied accessories | ||
| kHz, 0.1 % THD, at 1 ohms) |
| Mounting screws (4) |
| 50 W × 2 (20 Hz – 20 kHz, 0.03 % |
| Remote control lead (1) |
| THD, at 4 ohms) + 190 W × 1 | Optional accessories | |
| (20 Hz – 20 kHz, 0.08 % THD, at |
| Connecting cord for power |
| 4 ohms) with |
| amplifier |
| 95 W × 2 (20 Hz – 20 kHz, 0.08 % |
| RCA pin cord |
| THD, at 2 ohms) + 250 W × 1 |
| RCA pin cord |
| (20 Hz – 20 kHz, 0.1 % THD, at |
|
|
| 2 ohms) with |
|
|
| 190 W per channel with 2- | Design and specifications are subject to change | |
| speaker system (20 Hz – 20 kHz, | without notice. |
|
| 0.08 % THD, at 4 ohms) |
|
|
250 W per channel with 2- speaker system (20 Hz – 20 kHz, 0.1 % THD, at 2 ohms)
Stereo Power Amplifier
Operating Instructions
Mode d’emploi
Owner’s Record
The model and serial numbers are located on the bottom of the unit. Record the serial number in the space provided below.
Refer to these numbers whenever you call upon your Sony dealer regarding this product.
Model No.
XM-450G
Sony Corporation ©1995 Printed in Japan
Spécifications
Circuiterie | Alimentation par impulsions |
| avec circuit OTL (Output |
| transformless) |
Entrées | Prises à broche RCA |
Sorties | Bornes de |
Impédance des | |
| 1 – 8 ohms (stéréo) |
| 2 – 8 ohms (utilisé comme |
| amplificateur en pont) |
Sortie maximale | 100 W par canal pour le système |
à4
200 W par canal pour le système
à4
380 W par canal pour le système
à2
500 W par canal pour le système
à2
Sorties nominales (tension d’alimentation de 14,4 V)
50 W par canal pour le système à 4
20 kHz, 0,03 % DHT, à 4 ohms)
95 W par canal pour le système à 4
20 kHz, 0,08 % DHT, à 2 ohms)
125 W par canal pour le système
à4
20 kHz, 0,1 % DHT, à 1 ohm)
50 W × 2 (20 Hz – 20 kHz, 0,03% DHT, à 4 ohms) + 190 W × 1
(20 Hz – 20 kHz, 0,08 % DHT, à
4 ohms), pour le système à
3
95 W × 2 (20 Hz – 20 kHz, 0,08 % DHT, à 2 ohms) + 250 W × 1
(20 Hz – 20 kHz, 0,1 % DHT, à
2 ohms) pour le système à
3
190 W par canal pour le système
à2
20 kHz, 0,08 % DHT, à 4 ohms)
250 W par canal pour le système à 2
20 kHz, 0,1 % DHT, à 2 ohms) Réponse en fréquence
5 Hz – 100 kHz (
Distorsion harmonique
0,003 % ou inférieure (à 1 kHz, 4 ohms, 16 W)
Plage de réglage du niveau d’entrée 0,2 – 2 V
Filtre
Filtre
| 50 Hz, 80 Hz, |
Alimentation | Batterie de voiture, courant |
| continu 12 V (masse négative) |
Tension d’alimentation | |
| 10,5 – 16 V |
Courant | à la sortie nominale: 27 A |
| (4 ohms, 40 W × 4) |
| à 10 % de DHT: 32 A |
| Entrée télécommande: 5 mA |
Dimensions hors tout | |
| Env. 230 × 60 × 360 mm (l/h/p) |
| (9 1/8 × 2 3/8 × 14 1/4 po.) |
Poids | Env. 4,6 kg (10 li. 7 on.) |
accessoires non compris Accessoires fournis
Vis de montage (4)
Fil de commande à distance (1) Accessoires en option
Cordon de liaison pour amplificateur de puissance
Cordon à broche RCA
Cordon à broche RCA
La conception et les spécifications peuvent être modifiées sans préavis.
Features
•Rated power output of 50 watts per channel (at 4 ohms).
•The
•Dual mode connection possible a
•Protection circuit provided.
•Pulse power supply* for stable, regulated output power.
•New circuit which removes the source resistance from the final MOS FET output stage, and drives the speaker directly.
•Twin power supply with rectification circuits for each channel.
*Pulse power supply
This unit has a
Caractéristiques
•Puissance nominale de 50 watts par canal (à 4 ohms).
•Vous pouvez utiliser le
•Double mode de connexion pour un système avec plusieurs
•Equipé d’un circuit de protection. •Alimentation par impulsions* garantissant une
puissance de sortie stable et régulière. •Equipé d’un nouveau circuit qui supprime la
résistance de source de l’étage de sortie final du MOS FET et entraîne les
•Double alimentation avec circuits de redressement pour chaque canal.
*Alimentation par impulsions
Le convertisseur intégré de cet appareil permet de transformer l’alimentation en courant continu fournie par une batterie de voiture de 12 volts en signaux