Your Rubicon amplifier is protected against both overheating and short circuits by means of the following circuits:
+Main Power fuse
+Smart Power Supply Thermal Rollback activating at 85°C
+A failsafe thermal protection circuit activating at 95°C
NOTE: If you experience blown main power supply fuses, it is iikely‘ that the amplifier is seeing a dead short, either in the speaker wire or in the speaker itself. Rectify the problem before blowing multiple fuses! DO NOT increase values beyond the original fuse value! Doing so will void your warrant and may damage your amplifer.
PROBLEM | CAUSE | ||
|
|
| |
|
| 1. No power or ground at the amp | |
No sound and the power LED is not lit. | 2. No remote | ||
|
| 3. Blown fuse near battery | |
|
|
| |
Repeatedly blown amp fuse; frequent | 1. Speaker leads may be shorted | ||
2. Verify adequate amplifier ventilation | |||
activation of the Smart Power Supply | |||
3. Make sure you aren’t driving | |||
Circuit |
| ||
| subwoofersl | ||
|
| ||
|
| ||
No output from channels 3&4 with 1 | Set the Ch 3&4 input selector swith on | ||
pair of RCA inputs (Picasso only) | the top of the amp to “Ch l&2” | ||
|
| ||
Not enough input sensitivity while using | Be sure both Left and Right input signal | ||
Balanced DIN Input | switches are set to the “BALI’ position. | ||
|
|
| |
|
| Output signal level is too high and the | |
Left and Right “Clip” indicators lighting | amplifier output is clipping. Reduce the | ||
level either at the source or with the | |||
|
| ||
|
| input level controls. | |
|
|
| |
|
| 1. Make sure the channel 2 Input Signal | |
|
| Switch is in the “UNBAL” position. | |
Alternator whine | while using | 2. Try the Input Signal Switches for | |
channels 1, 3 & 4 in the “BAL” position: | |||
Unbalanced RCA | inputs | ||
leave the switches in the quitest | |||
|
| ||
|
| position. This will not effect the | |
|
| performance of the amp. | |
|
|
|
SERVICE
Your Soundstream RUBICON Class A amplifier is protected by a limited warranty. Please read the enclosed warranty card for details.
SPECIFICATIONS
|
|
|
|
|
| |
| 4 SZ Stereo | 2 a Stereo | Maximum | |||
POWER | (8 Sz Bridged) | (4 Sz Bridged) | Rated | |||
| (12.5 Vdc) | (12.5 Vdc) | output | |||
|
|
|
|
|
| |
PtCASSO | 25Wx4 | 5owx4 | 200 Watts | |||
(5OW x 2) | (1OOW x 2) | |||||
|
| |||||
|
|
|
|
|
| |
|
|
|
|
|
|
THD | co.1 % |
Signal to Noise | >I00 dB |
Frequency Response | 20 Hz to 20 kHz * 0.5 dB |
Stereo Separation | >90 dB |
Damping | >200 |
Input Sensitivity | 300 mV to 5.0 Volts |
Input Impedance | 1 Ok Ohms |
Dimensions (W x D x H)
PU4((0: 16.0” X 9.8” X 2.25” (406mmx288mmx57mm)
REEJOIR: 12.25” X 9.8” X 2.25” (330mmx288mmx57mm)
18
19