SOYO SY-K7VEMPRO 2-3.3.2 Floppy Drive Installation

Hardwa re Insta llation SY-K7VEMPRO

2-3.3.2 Floppy Drive Installation

The system supports 5 possible floppy drive types: 720 KB, 1.2 MB,

1.44 MB, 2.88 MB, and LS-120.

Connect one side of the 34-pin flat cable to the floppy drive and plug the

other end to the floppy drive connector on the Motherboard.

This Motherboard can support up to 2 floppy drives.

Lithium

Battery

RTL8139C

VT1611A

Flash BIOS

FDC

Pin -1

Floppy Drive

Connector

Contents

Main SY-K7VEMPRO Motherboard User's Manual SOYO FC 100% ii Edition: November 2001 Version 1.0 K7VEMPRO SERIAL C Table of Contents Page Chapter 1 MOTHERBOARD DESCRIPTION 1-1 INTRODUCTION 1-2 KEY FEATURES CPU SUPPORT CPU SETTINGS ADVANCED FUNCTIONS FAIL SAFE Hardware Monitor SOYO Bonus Pack CD-ROM COMPLIANCE USER FRIENDLY 1-3 HANDLING THE MOTHERBOARD 1-4 ELECTROSTATIC DISCHARGE PRECAUTIONS Motherboard Description SY-K7VEMPRO 4 1-5 SY-K7VEMPRO MOTHERBOARD LAYOUT Flash BIOS PCI Slot #1 PCI Slot #2 PCI Slot #3 1-6 SY-K7VEMPRO MOTHERBOARD COMPONENTS Page 1-7 MICROPROCESSOR 1-7.1 Microprocessor Packaging 1-7.2 Microprocessor Upgrades 1-8 MEMORY 1-8.1 Main Memory 1-9 CHIPSET Page Page 1-10 I/O INTERFACE CONTROLLER 1-10.1 Serial Ports 1-10.2 Parallel Port 1-10.3 Diskette Drive Controller 1-10.4 PS/2 Keyboard and Mouse Interface 1-10.5 Infrared Support 1-11 HARDWARE MONITOR 1-12 WAKE ON LAN TECHNOLOGY Chapter 2 HARDWARE INSTALLATION 2-1 PREPARATIONS 2-2 UNPACKING THE MOTHERBOARD 2-3 INSTALLATION GUIDE BEGIN THE INSTALLATION 2-3.1 CPU Installation Mark your CPU Frequency: Page Page CPU Fan Mount Procedure: Page Page 2-3.2 SDRAM Memory Module Installation Page 2-3.3 Motherboard Connector 2-3.3.2 Floppy Drive Installation FDC Pin -1 +_ Speaker Power / ACPI LED PWRBT Reset HDD LED +_ HDD LED Pin Assignment +_ PWRBT Pin Assignment Page Page Page Wake-On-LAN JP44 Pin Assignment 123 5VSB GND Wake up Standard Infrared (SIRCON1) Connector SIRCON Pin Assignment Page Page A TX Power ATX P ower 2-3.4 CPU FSB Setting (JP3) 2-3.5 CMOS Clearing (JP5) 2-3.6 Power On 2-3.7 Quick BIOS Setup 2-3.8 Troubleshooting at First Start Video (no display) related issues BIOS Issues Hard disk, floppy drive, CD-ROM etc Modem issues Audio Issues 2-3.9 Power Off Chapter 3 BIOS SETUP UTILITY Page Page 3-1 STANDARD CMOS SETUP 3-1.1 Date & Time 3-1.2 Hard Disks Type & Mode 3-1.3 Floppy Drives 3-1.4 Others Optional 3-2 ADVANCED BIOS FEATURES 3-2.1 Virus Warning 3-2.2 Cache Memory Options 3-2.3 Quick Power On Self Test 3-2.4 System Boot Control Settings 3-2.5 Floppy Driver Settings 3-2.6 Boot Up Floppy Seek 3-2.7 Boot Up NumLock Status 3-2.8 Gate A20 Options 3-2.9 Typematic Settings 3-2.10 Security Option 3-2.11 Other Control Options BIOS Setup Utility SY-K7VEMPRO 59 3-3 ADVANCED CHIPSET FEATURES 3-3.1 CHIPSET FEATURES SETUP Page Page Page 3-4 INTEGRATED PERIPHERALS 3-4.1 IDE Device Controls IDE 3-4.2 Display Controls 3-4.3 IDE HDD Block Mode 3-4.4 FDC Controls 3-4.5 Onboard Serial Ports 3-4.6 Onboard Parallel Ports 3-4.7 Onboard Legacy Audio Onboard Legacy Audio (Continued) 3-5 POWER MANAGEMENT SETUP 3-5.1 Power Management Controls Power Management Controls (Continued) Page 3-6 PNP/PCI CONFIGURATION SETUP 3-6.1 PNP/PCI Configuration Controls PNP/PCI Configuration Setup (Continued) 3-6.2 MULTI I/O ADDRESSES 3-7 PC HEALTH STATUS 3-7.1 CPU Device Monitoring 3-8 LOAD FAIL-SAFE DEFAULTS 3-9 LOAD OPTIMIZED DEFAULTS 3-10 SUPERVISOR PASSWORD 3-11 USER PASSWORD Enter Password: ress to exit After you confirm the 3-12 BOOT MENU Chapter 4 DRIVERS INSTALLATION Page Step 2. Install Drivers Page Step 3. Select which driver you want to install and click OK Step 4. Ch eck the Latest Releases Chapter 5 REALTEK LAN DRIVER INSTALLATION Install the Realtek LAN Drivers under windows 98 Install the Realtek LAN Drivers under windows NT4.0 Install the Realtek LAN Drivers under windows ME Install the Realtek LAN Drivers under windows XP Install the Realtek LAN Drivers under windows 2000