SpectraPure®

6.Re-insert the yellow tubing into its push-fitting in the RO membrane as follows:

a.)

Moisten the O-ring seal inside the concentrate outlet fitting by dripping

 

a few drops of clean water into the fitting.

b.)

Grasp the yellow tubing near the flow restrictor end, and insert the

 

tubing into the push-fitting. Push the tubing into the fitting until

 

resistance is felt, approximately 1/2 inch (12.7 mm). The tubing is now

 

resting on the O-ring seal inside the fitting.

c.)

Firmly push the tubing approximately an additional 1/4 inch

 

(6.35 mm) further into the fitting to completely seat the line into

 

the fitting and O-ring seal.

7.Turn on the system water supply and check for leaks prior to further use or testing. If a leak is observed, you may not have pushed the yellow tubing into the push-fitting far enough to seal the tubing against the O-ring. Turn off the system water supply and reseat the tubing as described above.

Fig. C: Reverse Osmosis Assembly

Top/Rear View

RO membrane

yellow concentrate tubing

(Waste Water)

membrane

 

feed

blue purified water

push-fitting

tubing

 

 

(Good Water)

black

black feed water

tubing to

tubing

membrane

(Tap Water)

feed

Fig. D: Flow Restrictor Assembly

SpectraPure®

SEDIMENT PRE-FILTER REPLACEMENT

For maximum contaminant removal and long membrane life, the sediment pre-filter must be changed when a 15-20% drop in pressure is observed OR at least 6-month intervals. If your water contains a great deal of sediment the pre-filter may require more frequent changes to maintain adequate production rate and extended membrane life.

Sediment Pre-Filter Replacement

Materials Required: 0.5-micron MicroTec™ Sediment Filter (SF-MT-0.5-10), Filter Wrench

Procedure: (FIRST FILTER ON LEFT)

1.Turn off water supply to the system.

2.Refer to photo on page 6. Using the provided filter wrench, remove the first housing on the left. Unscrew it counterclockwise as viewed from the bottom.

3.Remove the old filter and discard.

4.Thoroughly wash the housing with a mixture of hot soapy water and a few teaspoons of household bleach. Rinse well with clean hot water.

5.Install the new pre-filter into the housing, Screw the housing back onto the assembly, and hand tighten only.

NOTE: Do not use filter wrench to tighten housings. Over-tightening will damage housings and void your warranty.

6.Proceed with carbon block filter replacement.

CARBON BLOCK FILTER REPLACEMENT

For maximum contaminant removal and long membrane life, the carbon pre-filter must be changed at least ever 6-month or when chlorine breakthrough greater than 0.1 ppm occurs in the yellow concentrate line. Test for chlorine breakthrough by collecting a 10 ml sample of the concentrate from the yellow tubing and test the chlorine concentration using test kit TK-CL-10. If the chlorine concentration is above 0.1ppm, replace the carbon pre-filter.

yellow tubing

capillary tubing

Materials Required: 0.5 micron Carbon Block Filter (CF-0.5-10), Filter Wrench, Chlorine Test Kit (TK-CL-10)

plastic insert

 

SpectraPure®Inc. 480.894.5437 Call us toll-free 1.800.685.2783

12

2167 East Fifth St, Tempe, Arizona 85281

 

Procedure: (SECOND FILTER ON LEFT WHEN FACING SYSTEM)

1.Perform steps 1-5 listed above

2.Turn on system water supply and check for leaks.

SpectraPure®Inc. Fax 480.894.6109 Fax us toll-free 1.877.527.7873 E-mail: spectra@spectrapure.com Visit us on the web www.spectrapure.com 13

Page 11 Page 12
Page 12
Image 12
Spectra Watermakers SF-MT-0.5-10, MEM-90,150, CF-0.5-10 Sediment PRE-FILTER Replacement, Carbon Block Filter Replacement
Page 11 Page 12

CF-0.5-10, SF-MT-0.5-10, MEM-90,150 specifications

Spectra Watermakers is renowned for its advanced water desalination technology, providing reliable fresh water solutions for various applications. Among their notable products are the CF-0.5-10, SF-MT-0.5-10, MEM-90, and MEM-150 systems, each designed to meet specific water production needs while maintaining ease of use and efficiency.

The CF-0.5-10 model is a compact and highly efficient watermaker that delivers up to 10 gallons per hour. Its primary feature is reverse osmosis technology, which effectively removes salt and impurities from seawater, resulting in high-quality potable water. The system is equipped with an energy recovery device that minimizes energy consumption, making it a sustainable choice for boaters and coastal residents alike. With a lightweight design, the CF-0.5-10 is easy to install and maintain, ensuring that users can consistently access fresh water in remote locations.

The SF-MT-0.5-10 is another impressive model from Spectra Watermakers. It offers similar efficiency and capacity but includes additional features for marine applications. This model utilizes a high-quality stainless steel frame and marine-grade components, enhancing durability amidst harsh conditions. The SF-MT-0.5-10 includes an intuitive user interface, allowing for easy operation and monitoring of water production levels. Its compact size makes it suitable for installation in tight spaces on yachts or small vessels.

For those needing larger production capacities, the MEM-90 and MEM-150 systems provide impressive output. The MEM-90 can produce up to 90 gallons per day, while the MEM-150 takes it a step further with a daily capacity of 150 gallons. Both systems leverage advanced membrane technology, ensuring robust performance and long-term reliability. Features such as automatic pressure regulation and user-friendly digital controls provide operators with a seamless experience.

Additionally, these systems are designed with energy efficiency in mind, employing innovative technologies to reduce power consumption. Their rugged construction ensures that they can withstand various environmental stresses, making them ideal for use in both commercial and recreational settings.

In conclusion, Spectra Watermakers’ CF-0.5-10, SF-MT-0.5-10, MEM-90, and MEM-150 systems exemplify quality and innovation in water desalination. Each model brings unique features to meet diverse needs, ensuring that users have a reliable source of fresh water wherever they may be. Whether for marine use or land-based applications, Spectra’s watermakers guarantee performance, efficiency, and durability.
Top Page Image Contents